Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 52

Страница: 52 / 72

Technical data

SIMATIC RF170C

Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

6GT2002-0HD01

Mechanical data

Dimensions (W x H x D) in mm
•

Electronic module RF170C

90 x 130 x 35

•

RF170C connection module

90 x 130 x 60

Weight
•

Electronic module RF170C

approx. 270 g

•

RF170C connection module

approx. 500 g

Environmental conditions

Ambient temperature

•

During operation

–25 to +55 °C

•

During transportation and

storage

–40 to +70 °C

Degree of protection

IP67

MTBF (at 40°C)

77.5 years

Approvals

cULus (File E248953)

All supply and signal voltages must be safety extra low voltage (SELV/PELV according to

EN 60950) 24 VDC). Reliable (electrical) isolation of low voltage (SELV / PELV acc. to EN 60950)

The power supply must provide the required current of max. 1 A during brief power outages of

≤ 20 ms.

Содержание 6GT2002-0HD01









































































Результаты поиска

Содержание 6GT2002-0HD01

Отзывы:

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 52 / 72

Результаты поиска

Содержание 6GT2002-0HD01

Отзывы: