Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 46

Страница: 46 / 72

Diagnostics and error messages

7.2 LED displays on the RF170C communication module

SIMATIC RF170C

Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

Status and error LEDs on the RF170C connection module

Table 7- 1

Status and error LEDs for RF170C

LED

Meaning

Group error

ACT_1, ACT_2

The corresponding reader is active processing a user command. (MOBY only)

ERR_1, ERR_2

A flashing pattern indicates the last error to occur.

PRE_1, PRE_2

Indicates the presence of a transponder.

RxD_1, RxD_2

Indicates live communication between the CM and the reader. May also indicate

malfunctions on the reader.

The meaning of the individual flashing pattern is described in the relevant FB documentation.

There, you will also find the relevant error descriptions.

In the case of multitag operation, this LED uses a flashing interval to indicate the number of data

carriers currently within the range of the reader.

After start-up or updating the firmware, the LEDs SF, PRE, ERR and ACT indicate the operating

status or errorss of the RF170C:

Table 7- 2

Operating states

PRE_1

ERR_1

ACT_1

PRE_2

ERR_2

ACT_2 Description

Off

Startup active

Off

Checksum error at startup *

Off

Firmware invalid *

LED test for approximately 4 seconds;

otherwise firmware error *

Off

Checksum error at startup *

Off

Checksum error of the firmware *

Off

External RAM defective *

Off

ESSA3 defective *

Off

ID error firmware *

–

Off

1 x flash

every 3 s

Off

1 x flash

every 3 s

Off

RF170C successfully started up, waiting for

reset command

–

n x flash

every 3 s

–

m x flash

every 3 s

–

The last reported error in the channel can

be seen from the number of flashes (n, m).

–

Flashing

Rapid

flashing

–

Flashing

Rapid

flashing

Firmware update; alternate flashing of the

error LEDs at approximately 1 Hz

– = not relevant

* If this fault recurs, the module is defective and must be replaced.

Содержание 6GT2002-0HD01









































































Результаты поиска

Содержание 6GT2002-0HD01

Отзывы:

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 46 / 72

Результаты поиска

Содержание 6GT2002-0HD01

Отзывы: