Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 43

Страница: 43 / 72

Service and maintenance

6.4 Firmware update

SIMATIC RF170C
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

Replacing a (defective) RF170C

Follow the steps below to replace the CM RF170C:
1.

Loosen the 4 screws on the front panel of the connection module (top and bottom) using

the cross-head screwdriver.

Remove the connection module with the RF170C from the bus module.

Press the release button on the top of the RF170C while at the same time pulling the

connection module up and off the electronic module.

Remove one half of the coding element from the new RF170C (top left).

Insert the connection module onto the new RF170C.

Insert the connection module with the RF170C onto the bus module and secure it with the

screws.

Note
Removing/plugging in the reader cable

Removal and insertion of the reader cable is permissible under power. An "init_run" is

required after connecting a new reader.

NOTICE
Do not make any changes to the coding during the replacement.

Do not make any changes to the coding during the replacement to make sure that your

system continues to run free of errors..

NOTICE
Configuring the modules with the article number "6GT2002-0HD00"

The modules with article number "6GT2002-0HD00" will be completely replaced by the

modules with article number "6GT2002-0HD01". Note that if you configure the old modules

with one of the new modes (e.g. Freeport protocol) the modules will be inoperable. If the

old modules are configured with a new mode, no “desired/actual” error message will be

generated. Instead a parameter assignment error iis reported when the module starts up.

6.4

Firmware update

The firmware of the RF170C can be updated. The update takes place via STEP 7 (TIA Portal) or

the SIMATIC Manager.
You will find detailed information on the update in the operating instructions “ET 200pro

distributed I/O device (

https://support.industry.siemens.com/cs/ww/en/view/21210852

)“.

You will find the latest firmware version on the page of Siemens Industry Online Support

(

https://support.industry.siemens.com/cs/ww/en/view/24512084

Содержание 6GT2002-0HD01









































































Результаты поиска

Содержание 6GT2002-0HD01

Отзывы:

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 43 / 72

Результаты поиска

Содержание 6GT2002-0HD01

Отзывы: