Siemens 6ES7547-1JF00-0AB0 Скачать руководство пользователя страница 28

Страница: 28 / 41

Diagnostic alarms

5.1 Status and error displays

Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Manual, 03/2019, A5E45488510-AA

RUN and ERROR LED

Table 5- 1

Status and error displays RUN and ERROR

LED

Meaning

Solution

RUN

ERROR

Off

Voltage missing or too low at back-

plane bus.

•

Switch on the CPU and/or the sys-

tem power supply modules.

•

Verify that the U connectors are

inserted.

•

Check whether too many modules

are inserted.

Flashes

Off

The module starts up and flashes until

the valid parameter assignment is set.

Off

Module parameters are assigned.

Flashes

Indicates module errors (at least one

error is present on one channel, e.g.

wire break).

Evaluate the diagnostics and eliminate

the error (e.g. wire break).

Flashes Flashes

The hardware is defective.

Replace the module.

LED PWR

Table 5- 2

POWER status display

LED P

Meaning

Solution

Off

Supply voltage L+ too low or missing. Check the supply voltage L+.

On (green)

Supply voltage L+ is present and OK. -

Содержание 6ES7547-1JF00-0AB0










































Результаты поиска

Содержание 6ES7547-1JF00-0AB0

Отзывы:

Похожие инструкции для 6ES7547-1JF00-0AB0

Бренды по названию

Популярные бренды

Siemens 6ES7547-1JF00-0AB0, Руководство пользователя

Результаты поиска

Содержание 6ES7547-1JF00-0AB0

Отзывы:

Похожие инструкции для 6ES7547-1JF00-0AB0

Бренды по названию

Популярные бренды