Siemens 6ES7547-1JF00-0AB0 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 41

background image

Parameters/address space

4.3 Address space

Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Manual, 03/2019, A5E45488510-AA

23

Port configuration with S7-PCT

Requirements
You have cleared the "Port configuration without S7-PCT" check box in the configuration of

the IO-Link master in STEP 7.
Procedure
You configure the IO-Link Master ports with the Port Configuration Tool S7-PCT, V3.5 SP1

or higher. In doing so, select the IO-Link device from the device catalog of S7-PCT and

assign the device to an IO-Link port.

Port Qualifier Information (PQI)

You can activate the Port Qualifier Information (PQI) for your IO-Link Master.

Note
Port Qualifier Information (PQI)
If you have activated the Port Qualifier Information (PQI), it is always transferred with the

size 1 byte together with the input data of the IO-Link device.
PQI is not available for 8 bytes input / 8 bytes output.

The figure below shows the structure of the PQI byte.

«
...
22
23
24
25
26
...
»

Содержание 6ES7547-1JF00-0AB0










































Отзывы:

Нет отзывов

Похожие инструкции для 6ES7547-1JF00-0AB0

Бренд: Ubisys Страницы: 2

Бренд: DAV TECH Страницы: 10

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: Tech 21 Страницы: 2

Бренд: Procom Страницы: 10

Бренд: HANYOUNG NUX Страницы: 4

Бренд: FADAL Страницы: 2

Бренд: Veichi Electric Страницы: 8

Бренд: FUHR Страницы: 20

Бренд: Estyma Страницы: 9

Бренд: ILLUMINO IGNIS Страницы: 15

Бренд: PI Страницы: 111

Бренд: GSD Страницы: 2

Nuvo-3000 Series

Бренд: Neousys Technology Страницы: 101

easy2read Lepton3x1

Бренд: Caen RFID Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды