manualshive.com logo in svg

Siegenia AEROLIFE, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Siegenia AEROLIFE Скачать руководство пользователя страница 4

4

AEROLIFE 

Original operating instructions

08.2016

Target group of this documentation

This documentation is intended for use by specialists only. All work described in this document is to be performed by 
experienced professionals with training and practice in the assembly, installation and maintenance of ventilation units. Safe 
and proper assembly of this unit is not possible without expert knowledge.

Intended use

•  Use the AEROLIFE only for the ventilation of closed rooms (kitchen, bathroom, living room and bedroom).
•  The AEROLIFE is not suitable for dehumidification (e. g. for drying new buildings).
•  The unit must always be installed by an experienced specialist, in accordance with the installation and planning 

documents of SIEGENIA. The installation instructions in this document must be complied with at all times.

•  Be sure to attach the supplied SIEGENIA weather grille to protect the unit from the outside.
•  Do not install the unit in contaminated rooms and ensure that no hazardous substances can be drawn in.
•  The unit is not suitable for use in swimming pools and/or damp locations.
•  The AEROLIFE may only be mounted in a vertical position. The unit may not be installed on diagonal surfaces (e. g. 

walls/ceilings).

•  If the unit is to be used in a room with a heating unit that draws air from the room, prior authorisation must be obtained 

from the proper authorities, such as the officially appointed district chimney sweep.

•  Only operate and/or store the AEROLIFE at temperatures between -15 °C and +40 °C.
•  Use the device only with original accessories from SIEGENIA.
•  Observe the safety regulations for working with ladders, steps, overhead work and work at particular heights.
•  Use the device only when it is in a technically sound condition. 
•  Do not modify the unit‘s components in any way.
•  Please do not put any objects on top of the unit.
•  Do not use the unit as a seat.
•  Ensure that the air can flow in and out freely at the two outer sides. Do not hang any textiles, paper or similar objects over 

the air inlets or outlets and do not place any objects directly in front of or next to the unit. Do not insert objects into the 
openings of the unit.

•  Do not remove any covers or unit components except as described in the chapter „Maintenance“. Do not remove the 

cover of the connecting clamps inside the unit.

•  The device must be checked by a specialist in the event of a fault.

Содержание AEROLIFE

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды