SICK UE4740 Скачать руководство пользователя

Страница: 29 / 44

Operating Instructions

Chapter

UE4740

8020182/1CUO/2022-08-26

Subject to change without notice

Fault diagnosis

8.3

Error displays of the LEDs

This section explains what the LED error displays mean and how you can respond. Please
refer to the description in the section 3.2

“

Display elements

” on page

12ff.

8.3.1

Error displays of the EFI gateway

Display

Possible cause

How to remedy the error

PWR



No power supply



Check the voltage supply and
activate, if necessary.



Red

Internal voltage supply too
low or firmware is being
updated



If necessary, check the voltage
supply.

DIA



Red

Configuration has not been
completed or is being
transferred



The display goes off automatically
once the configuration has been
successfully transferred.

If the display does not go off:



Check the configuration of the
system using the CDS
(Configuration & Diagnostic
Software).



Re-transfer the corrected
configuration to the system.



Red

1 Hz: System error

(lock-out)



Check the device state by means of
the CDS diagnostics.



Eliminate any errors.



Disconnect the EFI gateway briefly
from the supply voltage.



If the problem persists, replace the
EFI gateway.

EFI1

and

EFI2



Red

Device communication error

at the EFI connection



Device not connected. Check the
connecting cable.



Device is not configured for the EFI
connection. Configure it using the
CDS (Configuration & Diagnostic
Software).

Tab. 8: Error displays of the

LEDs at the EFI gateway

Содержание UE4740












































Результаты поиска

Содержание UE4740

Отзывы:

Похожие инструкции для UE4740

Бренды по названию

Популярные бренды

SICK UE4740, Руководство по эксплуатации

Результаты поиска

Содержание UE4740

Отзывы:

Похожие инструкции для UE4740

Бренды по названию

Популярные бренды