manualshive.com logo in svg

SICK Lector61 Series, Руководство по эксплуатации

Поделиться
Скачать
SICK Lector61 Series Скачать руководство пользователя страница 55

11

Technical data

NOTE

The relevant online data sheet for your product, including technical data, dimensional
drawing, and connection diagrams can be downloaded, saved, and printed from the
Internet:

•

www.sick.com/Lector61x

Please note: This documentation may contain further technical data.

11.1

Features

Type

Lector610

Lector611

Focus

Depends on type, 

see "Type code", page 12

.

Optical focus methods

•

Adjustable focus with focus adjustment tool

•

Liquid lens, automatic focus adjustment

Sensor resolution

Depends on type, 

see "Type code", page 12

.

Integrated illumination
unit

8 LEDs:

•

4 LEDs with visible amber light (λ = 617 nm ± 50 nm)

•

4 LEDs with visible blue light (λ = 470 nm ± 15 nm)

Feedback LED (spot in field
of view)

1 LED:

•

Visible green light (λ = 525 nm ± 15 nm)

•

Visible red light (λ = 635 nm ± 15 nm)

LED alignment aid (2
points in the field of view)

2 LEDs, can be deactivated:
Visible red light (λ = 630 nm ± 15 nm)

LED risk group

Integrated illumination unit:

Risk group 1 (low risk) according to IEC 62471-1: 2006-07 / EN
62471-1: 2008-09 including EU Directive 2006/25 / EC (DIN EN
62471:2009-03 is identical to EN 62471:2008-09).

Radiance

•

L

B

 

1)

: < 10 x 10

3

 W/(m

2

sr) within 100 seconds; at distance

≥ 200 mm

•

L

R

 

2)

: < 2.2 x 10

6

 W/(m

2

sr) within 10 seconds; at dis‐

tance ≥ 200 mm

Distance-dependent hazard value

•

Risk group 0 (no risk) based on L

B

 

1)

: < 100 W/(m

2

sr) within

10,000 seconds; at a distance of > 2.0 m.

Feedback LED, LED alignment aid and status LEDs

:

Risk group 0 (no risk) according to IEC 62471-1: 2006-07 / EN
62471-1: 2008-09 including EU Directive 2006/25 / EC (DIN EN
62471:2009-03 is identical to EN 62471:2008-09).

MTBF of LEDs

Integrated illumination unit, feedback LED and LED alignment
aid:

75,000 h, at 25 °C ambient operating temperature

Time-of-flight sensor

1 laser (distance measurement in configuration mode):
Invisible infrared light (wavelength 940 nm, maximum output
power ≤ 17.5 mW, pulse length ≤ 3.7 ns)

Laser class

Time-of-flight sensor:

Class 1 Laser Product according to EN/IEC 60825-1:2014. Com‐
plies with 21 CFR 1040.10 except for conformance with IEC
60825-1 Ed. 3.0 as described in “Laser Notice 56” dated May
8, 2019.

TECHNICAL DATA 

11

8024830/1FGB/2022-03-29 | SICK

O P E R A T I N G   I N S T R U C T I O N S | Lector61x

55

Subject to change without notice

Содержание Lector61 Series

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды