manualshive.com logo in svg

SICK Lector61 Series, Руководство по эксплуатации

Поделиться
Скачать
SICK Lector61 Series Скачать руководство пользователя страница 41

Wiring data interfaces via a connection module

Connection modules

Data interface

Reference

CDB650-204

RS-232

see "Wiring serial host inter‐
face RS-232 of the device in
CDB650-204", page 64

CDM420-0006

RS-232

see "Wiring serial host interface
RS-232 of the device in the
CDM420-0006", page 73

6.5.4

Wiring the CAN interface

NOTE

Activate the CAN data interface in the device with a configuration tool, e.g., the configu‐
ration software SOPAS ET.
Make further settings in the device corresponding to the function of the device in the
system configuration.

Wiring CAN interfaces via a connection module

Connection modules

Interface

Reference

CDB650-204

CAN

see "Wiring the CAN interface of
the device in the CDB650-204",
page 65

CDM420-0006

CAN

see "Wiring the CAN interface of
the device in the CDM420-0006",
page 74

6.5.5

Wiring the digital inputs

The device has 2 switching digital inputs (Sensor1, Sensor 2).

Functions (examples)

•

Start and end external reading cycle.

•

Feed in incremental signal.

Position of digital inputs

•

Male connector of the device cable (M12, 17-pin, A-coded)

•

Adapter cable (female connector, M12, 17-pin, A-coded/male connector, D-Sub-
HD, 15-pin)

•

Open end of the adapter cable (female connector, M12, 17-pin, A-coded/open
end)

All digital inputs are available at the individual positions.

Signal 

3

52.3 K

3 K

"

§

$

Sensor GND 

V

S 

2

V

S

V

S

V

in 

5

!

PNP sensor 

1

GND

GND

Switching input of device 

4

GND

V

S

Figure 24: Wiring a digital input

1

Trigger sensor (PNP sensor)

ELECTRICAL INSTALLATION 

6

8024830/1FGB/2022-03-29 | SICK

O P E R A T I N G   I N S T R U C T I O N S | Lector61x

41

Subject to change without notice

Содержание Lector61 Series

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды