manualshive.com logo in svg

SICK Lector61 Series, Руководство по эксплуатации

Поделиться
Скачать
SICK Lector61 Series Скачать руководство пользователя страница 40

6.5.3

Wiring the data interface

Wiring the Internet interface

1.

Connect the device to the Ethernet connection of the computer via the adapter
cable.

2.

Set up communication via the SOPAS ET configuration software.

NOTE

The Ethernet interface of the device has an Auto-MDIX function. This automatically
adjusts the transmission speed as well as any necessary crossover connections.

Wiring the serial data interface

NOTE

The serial data interface is available only as a host interface for this device.

The maximum data transmission rate for the serial interface depends on the length of
cable and on the type of interface.

Table 8: Data transmission rates and recommended maximum lengths of cable

Interface

Data transmission rate

Distance to the target computer
(host)

RS-232

Up to 19.2 kBd

Max. 15 m

38.4 kBd ... 57.6 kBd

Max. 5 m

115.2 kBd … 500 kBd

< 2 m

NOTICE
Risk of damage to the internal interface modules!

If the serial data interfaces are wired incorrectly, then electronic components in the
device could get damaged.

■

Observe the information on wiring.

■

Carefully check the wiring prior to switching on the device.

RS-232

2

3

4

Device 

1

Host

TxD

RxD

GND

RxD

TxD

GND

Figure 23: Wiring of the RS-232 serial data interface

1

Device

2

...

4

Pin assignment: see RS-232 pin assignment for the respective device

NOTE

Activate the serial data interface type in the device using a configuration tool, e.g., the
SOPAS ET configuration software.

6 

ELECTRICAL INSTALLATION

40

O P E R A T I N G   I N S T R U C T I O N S | Lector61x

8024830/1FGB/2022-03-29 | SICK

Subject to change without notice

Содержание Lector61 Series

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды