manualshive.com logo in svg

SICK Flexi Classic, Руководство по эксплуатации

Поделиться
Скачать
SICK Flexi Classic Скачать руководство пользователя страница 97

Operating Instructions 

Chapter 

9

Flexi Classic Gateways

 

8011834/YT28/2016-03-15 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

97 

Subject to change without notice 

EtherNet/IP Gateway 

Overview of the selection and entry fields: 

Selection/entry 
window 

Factory 
setting 

Description 

Rx (To PLC) 
Transfer Mode 

Polling  

Determines the type of data transfer from 
UE410

F

EN1 to the PLC. 

Polling 

— PLC requests the data. 

Write-to-Tag/File 

— UE410-EN1 writes the data to 

the PLC memory. 

Off 

— PLC Interface disabled. 

See 
section 
9.4.1 

Tx (From PLC) 
Transfer Mode 

PLC Writes 

Determines the type of data transfer from the PLC 
to UE410-EN1. 

PLC Writes

 — PLC writes to the UE410-EN1 

memory. 

Read-from-Tag/file

 — UE410-EN1 requests data 

continuously from the PLC. 

Off 

— PLC Interface disabled. 

See 
section 
9.4.2 

Settings for the operating modes Write-to-Tag/File and/or Read-from-Tag/file: 

PLC IP Address  

0.0.0.0 

Specifies the PLC address in standard format xxx.xxx.xxx.xxx. 
The selected data sets are transferred to this IP Address. 

PLC Controller Slot 
Number 

0

Specifies the PLC slot number of the controller (typically 0). 

Settings for the operating mode Write-to-Tag/File: 

Maximum PLC 
Update Rate 

40 

Defines the maximum rate (the minimum time interval) for 
sending the data sets to the PLC. Settings occur dependent on 
the PLC processing speed. 
Minimum = 10 ms, maximum = 65535 ms. The default value of 
40 ms is suitable for most PLCs. 

Note

: If this value is greater than the Heartbeat Update Interval, 

the Heartbeat Update Interval is increased (slowed down) to 
this value.  

Enable Heartbeat 
Message 

Deactivated

Activates updating of the active data sets with the set 
Heartbeat Update Rate.  

Note

: Either this option or Update Immediately on Status/Confi-

guration Change must be activated, otherwise no data will be 
transferred! 

Heartbeat Update 
Interval 

5000 

Specifies the Heartbeat Update Interval in milliseconds with 
which the data are updated in the PLC. 
Standard = 5000 ms, Minimum = 10 ms, Maximum 
= 65535 ms. 

Note

: If the Maximum PLC Update Rate is larger than the 

Heartbeat Update Rate, the Heartbeat Update Rate is in-
creased (slowed down) to this value. 

Update 
Immediately on 
Status/Configu-
ration Change 

Deactivated

Specifies whether the UE410-EN is to update the data in the 
PLC immediately when changes occur in the data sets. If not 
activated, the update is carried out with the next Heartbeat 
Interval. 

Note

: Either this option or Enable Heartbeat Message must be 

activated, otherwise no data will be transferred! 

Tab. 91: Configuration of the 
interface to the PLC 

Содержание Flexi Classic





























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды