manualshive.com logo in svg

SICK Flexi Classic, Руководство по эксплуатации


Поделиться
Скачать
background image

Chapter 

10

 

Operating Instructions 

Flexi Classic Gateways

 

144

 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

8011834/YT28/2016-03-15 

Subject to change without notice 

PROFINET IO Gateway 

Error type 

Message 

0x41b 

Self diagnostics error: Error invalid bits in the output configuration. Contact SICK 

service. 

0x41c-0x4ff 

Self diagnostics error: Contact SICK service. 

0x501-0x5ff 

Internal input test error: Internal test pulse not present on Ix. Contact SICK service.

0x601-0x6ff 

External input test error: External test pulse not present on Ix. Check IO cabling. 

Contact SICK service if problem persists. 

0x701 

Output test error: Output X1 not off. Check IO cabling for any cross circuits. 

0x702 

Output test error: Output X2 not off. Check IO cabling for any cross circuits. 

0x703 

Output test error: Cross-circuiting OSSD. Check IO cabling. 

0x704 

Output test error: Output X3 not off. Check IO cabling for any cross circuits. 

0x705-0x707 

Output test error: Short circuit on several outputs (bit mask). Check IO cabling. 

0x708 

Output test error: Output X4 not off. Check IO cabling for any cross circuits. 

0x709-0x70f 

Output test error: Short circuit on several outputs (bit mask). Check IO cabling. 

0x710 

Output test error: Output X1 not on. Check IO cabling for any short circuits. 

0x711-0x71f 

Output test error: Short circuit on several outputs (bit mask). Check IO cabling. 

0x720 

Output test error: Output X2 not on. Check IO cabling for any short circuits. 

0x721-0x73f 

Output test error: Short circuit on several outputs (bit mask). Check IO cabling. 

0x740 

Output test error: Output X3 not on. Check IO cabling for any short circuits. 

0x741-0x77f 

Output test error: Short circuit on several outputs (bit mask). Check IO cabling. 

0x780 

Output test error: Output X4 not on. Check IO cabling for any short circuits. 

0x781-0x7ff 

Output test error: Short circuit on several outputs (bit mask). Check IO cabling. 

0x801 

Voltage monitoring error: Undervoltage I/O. Check power supply. 

0x802 

Voltage monitoring error: Undervoltage power supply unit. Check power supply. 

0x803 

Voltage monitoring error: Undervoltage power supply unit and undervoltage I/O. 

Check power supply. 

0x804 

Voltage monitoring error: Overvoltage I/O. Check power supply. 

0x805-0x807 

Voltage monitoring error: Refer to the user manual for further details on this error 

code. 

0x808 

Voltage monitoring error: Overvoltage power supply unit. Check power supply. 

0x809-0x81f 

Voltage monitoring error: Refer to the user manual for further details on this error 

code. 

0x820 

Voltage monitoring error: Error in power supply monitoring. Check power supply. 

0x821-0x8ff 

Voltage monitoring error: Refer to the user manual for further details on this error 

code. 

0x901 

Configuration/diagnostics error: Modules incompatability. Check Flexi Classic 

module revision and type for system requirements. 

0x902 

Configuration/diagnostics error: Configuration modification detected. 

0x903-0x908 

Configuration/diagnostics error: Refer to the user manual for further details on 

this error code. 

0x909 

Configuration/diagnostics error: SDO client has invalid state. Contact SICK service.

0x90a 

Configuration/diagnostics error: Unknown SDO-cnf. Contact SICK service. 

0x90b 

Configuration/diagnostics error: Unused SDO index. Contact SICK service. 

0x90c 

Configuration/diagnostics error: SDO #7 in slot list missing for at least one 

module. Contact SICK service. 

0x90d 

Configuration/diagnostics error: Index error in slot list. Contact SICK service. 

0x90e 

Configuration/diagnostics error: Invalid position switch 0. Check switch settings. 

0x90f 

Configuration/diagnostics error: Invalid position switch 1. Check switch settings. 

Содержание Flexi Classic





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flexi Classic

Handicare VR2 User Manual preview
VR2
Бренд: Handicare Страницы: 56
Datel Wireless Blade FX Controller for Wii Instruction Card preview
Wireless Blade FX Controller for Wii
Бренд: Datel Страницы: 2
Belden GRASS VALLEY MDX-3901 Manual To Installation And Operation preview
GRASS VALLEY MDX-3901
Бренд: Belden Страницы: 45
Maximum Controls MAX ARM Installation And Owner'S Manual preview
MAX ARM
Бренд: Maximum Controls Страницы: 58
SPX FLOW Waukesha Cherry-Burrell D4 Series Instruction Manual preview
Waukesha Cherry-Burrell D4 Series
Бренд: SPX FLOW Страницы: 34
FrSky R9M Instruction Manual preview
R9M
Бренд: FrSky Страницы: 2
Quantum R-net Basic Operation Instructions preview
R-net
Бренд: Quantum Страницы: 20
EOS InfraStyle Operating Instructions Manual preview
InfraStyle
Бренд: EOS Страницы: 84
Z-Wave HKZW-STICK Operating Manual preview
HKZW-STICK
Бренд: Z-Wave Страницы: 3
Nautronic NAUCON-40 User Manual preview
NAUCON-40
Бренд: Nautronic Страницы: 6
Redbusbar CircuitSpy 80 Installation And Operation Manual preview
CircuitSpy 80
Бренд: Redbusbar Страницы: 12
SystemAir fantech ECO-FEEL 414729 Installation And Operation Instructions preview
fantech ECO-FEEL 414729
Бренд: SystemAir Страницы: 2
Intellitec iConnex User Manual preview
iConnex
Бренд: Intellitec Страницы: 16
nano sensorics TEMPHU Operation And Installation Manual preview
TEMPHU
Бренд: nano sensorics Страницы: 6
HEIDENHAIN LIP 471R Mounting Instructions preview
LIP 471R
Бренд: HEIDENHAIN Страницы: 32
Velleman WS8426 User Manual preview
WS8426
Бренд: Velleman Страницы: 34
Conbraco Industries Apollo 70-600 Series Installation, Operation And Maintenance Manual preview
Apollo 70-600 Series
Бренд: Conbraco Industries Страницы: 4
Ravel RE - 104 Installation, Commissioning & Operating Manual preview
RE - 104
Бренд: Ravel Страницы: 33

Бренды по названию

Популярные бренды

Загрузить еще бренды