SICK Flexi Classic Скачать руководство пользователя страница 75

Страница: 75 / 156

Operating Instructions

Chapter

Flexi Classic Gateways

8011834/YT28/2016-03-15

Subject to change without notice

Ethernet TCP/IP Gateway

Click

Socket

to edit any of the four socket interfaces. The following web page is

displayed:

Enter the

Listen Port

number that is more appropriate to the user application.

Port 9000 and port 9001 are reserved and shall not be configured.
Set Connect To Mode to

Never

if the application shall connect to the UE410-EN.

Activate

Save in Flash

and click

Submit

to save the selection or continue configuration.

When a reserved port has been entered as

Listen Port

, a special web page will be dis-

played upon

Submit

. The following page will be displayed:

Select

Use default Listen Port of

to reset the Listen Port configuration to the valid

default port number of the socket. If this checkbox remains unchecked, the invalid port
number will remain entered when returning back to the configuration page and shall
still be changed to another value.
Click

Submit

to return to the

Edit Socket N Configuration

web page.

Note

Содержание Flexi Classic





























































































































































Результаты поиска

Содержание Flexi Classic

Отзывы:

Похожие инструкции для Flexi Classic

Бренды по названию

Популярные бренды

SICK Flexi Classic, Руководство по эксплуатации

Результаты поиска

Содержание Flexi Classic

Отзывы:

Похожие инструкции для Flexi Classic

Бренды по названию

Популярные бренды