manualshive.com logo in svg

SICK deTem4 Core Ex, Руководство по эксплуатации

Поделиться
Скачать
SICK deTem4 Core Ex Скачать руководство пользователя страница 39

7

Commissioning

7.1

Safety

Important information

DANGER

Hazard due to lack of effectiveness of the protective device
When changes are made to the machine, the effectiveness of the protective device may
be affected unintentionally.

b

After every change to the machine and changes to the integration or operational
and secondary conditions of the multiple light beam safety device, check the pro‐
tective device for effectiveness and recommission as specified in this chapter.

DANGER

Dangerous state of the machine

b

Make sure that the dangerous state of the machine is (and remains) switched off
during mounting, electrical installation, and commissioning.

b

Make sure that the outputs of the multiple light beam safety device do not affect
the machine during mounting, electrical installation, and commissioning.

WARNING

Hazard due to lack of effectiveness of the protective device

b

Before commissioning the machine, make sure that the machine is first checked
and released by qualified safety personnel.

b

Only operate the machine with a perfectly functioning protective device.

DANGER

Hazard due to lack of effectiveness of the protective device
Persons and parts of the body to be protected may not be recognized in case of non-
observance.

b

Make sure that the optical properties of the front screens of the sender and
receiver are not changed, e.g., by:

°

Beading water, mist, frost, or ice formation. If applicable, remove films or
other types of contamination, disconnect the voltage supply of the receiver
and then switch it back on.

°

Scratches or damage. Replace the device whose front screen is scratched or
damaged.

b

Make sure that all reflective surfaces and objects maintain a minimum distance
from the light beams.

b

Make sure that no dispersive media (e.g., dust, fog, or smoke) are within the calcu‐
lated minimum distance from the light beams.

Further topics

•

"Minimum distance from reflective surfaces", page 17

COMMISSIONING 

7

8020453/14Q7/2020-04-27 | SICK

O P E R A T I N G   I N S T R U C T I O N S | deTem4 Core

39

Subject to change without notice

Содержание deTem4 Core Ex





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды