Shuttle AN51R Скачать руководство пользователя страница 16

Страница: 16 / 75

- 9 -

System memory supports 64/128/256/512Mb technologies up to 3GB
capacity max and 1GB per DIMM.

AGP Expansion Slot

Provides single 1.5V 8x AGP slot which supports 4X / 8X AGP devices.

PCI Expansion Slots

It provides five PCI slots and supports 5788 Gigabit Lan (GbE)/VT6307 2
ports IEEE 1394 firewire on board.

8 USB 2.0/1.1 Interface Onboard

4X USB ports on back panel and two extended USB headers (4 ports) on front
panel.

Gigabit Ethernet Controller (BCM5788KFB)

10/100/1000 Mbps operation rate. Support Wake-on-Lan (WOL) function.

IEEE 1394 (VT6307)

Compliant with 1394 OHCI specification revision V1.0 and V1.1. Support
400Mb/s, 200Mb/s, 100Mb/s data transfer rate.

I/O Interface

Provides a variety of I/O interfaces:

1 x PS/2 Mouse

1 x PS/2 Keyboard

1 x Serial port

1 x Parallel port

1 x Clear CMOS button

1 x SPDIF-In port

1 x 1394 port

4 x USB ports

1 x Gigabit Lan port

1 x Mic-In port

1 x Center /Bass Out port

1 x Line-In port

1 x Rear-Out port

1 x SPDIF-Out port

1 x Front-Out port

Содержание AN51R












































































Результаты поиска

Содержание AN51R

Отзывы:

Похожие инструкции для AN51R

Бренды по названию

Популярные бренды

Shuttle AN51R, Руководство пользователя

Результаты поиска

Содержание AN51R

Отзывы:

Похожие инструкции для AN51R

Бренды по названию

Популярные бренды