Shuttle AN51R Скачать руководство пользователя страница 65

Страница: 65 / 75

- 58 -

Clock Spread Spectrum

This item allows you to set the Clock spread spectrum modulation.

The choice: Enabled or Disabled.

HT Frequency

This item allows you to set the HT Frequency.

The choice: 1X, 2X, 3X, 4X or 5X.

Special I/O for PCI Card

This item enable/disable the Special I/O for PCI Card.

The choice: Enabled or Disabled.

Base I/O Address

This item allows you to set the Base I/O Address.

The choice: 0000~FFFF.

I/O Length

This item allows you to set the I/O Length.

The choice: 1 Byte, 4 Bytes, 8 Bytes, 16 Bytes, 32 Bytes, 64 Bytes,
128 Bytes or 256 Bytes.

System BIOS Cacheable

Select Enable allows caching of the system BIOS ROM at F000h~FFFFFh,
resulting in better system performance. However, if any program is writen
to this memory area, a system error may result.

The choice: Enabled or Disabled.

Содержание AN51R












































































Результаты поиска

Содержание AN51R

Отзывы:

Похожие инструкции для AN51R

Бренды по названию

Популярные бренды

Shuttle AN51R, Руководство пользователя

Результаты поиска

Содержание AN51R

Отзывы:

Похожие инструкции для AN51R

Бренды по названию

Популярные бренды