Shuttle AN51R Скачать руководство пользователя страница 38

Страница: 38 / 75

- 31 -

IEEE 1394 Port Connector

This mainboard offers one 1394 port on
back-panel. Plug device jack into an avail-
able 1394 connector.

USB Port Connectors

This mainboard offers 4 USB ports on back
panel. Plug each USB device jack into an
available USB0~USB3 connector.

Gigabit LAN Port Connector

This mainboard can accommodate one
device on LAN. Attach a LAN cable to the
LAN port at the back-panel of your com-
puter.

Mic-In Port Connector

Mic-In is a 1/8-inch jack that provides a
mono input. It can use a dynamic mono
or stereo microphone with a resistance of
not more than 600 Ohms.

Mic-InPort

Gigabit LAN Port

IEEE 1394 Port

USB Port 0/1

USB Port 2/3

Center/Bass Out Port Connector

Center/Bass is a stereo output port through
which the combined signal of all internal
and external audio sources on the board
is output. It can be connected to 1/8-inch
TRS stereo headphones or to bass/center
amplified speakers.

Center/Bass Out Port

B10

Содержание AN51R












































































Результаты поиска

Содержание AN51R

Отзывы:

Похожие инструкции для AN51R

Бренды по названию

Популярные бренды

Shuttle AN51R, Руководство пользователя

Результаты поиска

Содержание AN51R

Отзывы:

Похожие инструкции для AN51R

Бренды по названию

Популярные бренды