ShoreTel SA-100 Скачать руководство пользователя страница 30

Страница: 30 / 84

SA-100 Planning, Installation, and Administration Guide

Chapter 4: Site Requirements and Preparation

4.3

Power Cable

Each SA-100 ships with a power cable. If you do not receive the correct power cable

for your environment, contact your ShoreTel partner or ShoreTel technical support.

NOTE

ShoreTel recommends that you connect the SA-100 to a reputable surge

protector or uninterruptable power supply (UPS).

4.4

Ethernet Ports

The SA-100 uses an auto-sensing, 10/100/1000 Ethernet interface. Two RJ-48C

Ethernet connections (GB1 and GB2) are provided to provide fault-tolerant

deployment. The ports use the same MAC Ethernet address and IP address but are

independent of each other and can be used in any sequence. However, when both

ports are connected, only one will be active at a time. Should the active interface lose

the link, the other interface is made active. You must use Category 5 or higher

cabling.

Table 4-4

SA-100 Rear Panel Indicators and Connectors

Item

Indicator, Button, or
Connector

Description

iDRAC6 Enterprise

port

Not used.

Serial connector

(DB9)

Connects a serial device to the system. Used to

configure static IP address.

VGA Connector

Not used.

eSATA

Not used.

(2) USB Connectors Allows you to connects USB devices to the unit for

system recovery. The ports are USB 2.0-compliant.

(2) Ethernet

Connectors

Supports 10base-T, 100base-T and 1000base-T

connections.

7, 8

System

identification button

and indicator light

These front and back panel buttons can be used to

locate a particular system within a rack containing

multiple appliances. When a button is pushed, both

front and back indicators light until the button is

pushed again, allowing the specific appliance to be

easily located.

Power supply

connector

Allows you connect power to the unit.

Retention clip

Secures the power cable.

Содержание SA-100





















































































Результаты поиска

Содержание SA-100

Отзывы:

Похожие инструкции для SA-100

Бренды по названию

Популярные бренды

ShoreTel SA-100, Руководство по установке

Результаты поиска

Содержание SA-100

Отзывы:

Похожие инструкции для SA-100

Бренды по названию

Популярные бренды