Shively Labs 6822 Скачать руководство пользователя страница 52

Страница: 52 / 78

Installing the De-icer System (if applicable)

f. Inside each junction box, connect the leads as shown in

, using wire

nuts (7) to secure the connections.

g. Repeat for the remaining bays, junction boxes, and interbay cables.
h. Secure the interbay cables to the mounting pipe or tower leg, using tie-

wraps.

i. Connect the 10-foot pigtail at the bottom of the bottommost junction box.

Installing the tower

junction box

CAUTION

It is important to ground both the tower junction box and the control

box, as shown in the schematic diagrams.

a. Furnish a tower junction box as shown schematically in

Figure 34

to connect

the antenna’s de-icer harness to the main power.

b. Run the ten-foot de-icer pigtail to the tower junction box and secure it to the

mounting pipe and/or the tower.

Installing the thermostat

(if applicable)

If you are using a thermostat, you may locate and mount it at your discretion.

We recommend mounting it as close as practical to the antenna.

CAUTION

When testing the thermostat, be sure to have one or both thermostat

leads disconnected before taking resistance readings. Otherwise, read-

ings may be affected by other components.

a. Before you connect the thermostat, measure the resistance across the

thermostat circuit and from it to ground to ensure that there are no short-

circuits. Thermostat readings should be as shown in

Table 4

on page 44.

b. Mount the thermostat near the antenna and connect the thermostat leads to

points S1 and S2 in the control box as shown in the schematic diagram,

Figure 34

Table 4. Thermostat readings

Reading

Location

Ambient

Temperature

Resistance =

0 ohms

(short circuit)

Resistance =

infinite ohms

(open circuit)

Leg-to-

Ground

Any

Defective thermo-

stat or shorted

leads

Leg-to-Leg

Above about 38° F

(3.3° C)

Defective thermo-

stat or shorted

leads

Between about 10°

and about 38° F

(-6.7° to 3.3° C)

Defective thermo-

stat or broken leads

Below about 10° F

(-6.7° C)

Defective thermo-

stat or shorted

leads

Содержание 6822















































































Результаты поиска

Содержание 6822

Отзывы:

Shively Labs 6822, Инструкция по установке, эксплуатации и техническому обслуживанию, Страница: 52 / 78

Результаты поиска

Содержание 6822

Отзывы: