Shively Labs 6822 Скачать руководство пользователя страница 5

Страница: 5 / 78

Table of Contents

Chapter 1 Preparation........................................................................ 1

Check the shipment............................................................................... 1
Torque specifications............................................................................. 1

Table 1 Torque specifications ..................................................... 1

Check the parts..................................................................................... 1
Set up the mounting location. ................................................................ 1

Tower-leg mount.............................................................................. 2
Support-pipe mount.......................................................................... 2
Top-mounted support pipe................................................................ 2
Preparing the tower leg or mounting pipe .......................................... 2

Chapter 2 Bay Assembly...................................................................13

Attach the mount to the bay weldment................................................. 13

Mounting pipe size to 3-1/2 inches outside diameter:........................ 13
Mounting pipe size 3-1/2 inches to six inches outside diameter:......... 13

Figure 11 Mount attachment, pipe size up to 3-1/2 inches .......... 14
Table 2 Mounting U-bolt usage................................................ 14
Figure 12 Mount attachment, pipe size 3-1/2" to 6".................... 15

Attach the bay arms. ........................................................................... 15

Figure 13 Bay arm attachment.................................................. 16

Attach the bay cable (single-bay antenna only) ..................................... 16
Attach the feedstraps to the endseal. ................................................... 16

Figure 14 Bay cable & feedstrap attachment (bay cable for single-bay

antenna only) ................................................................. 17

Chapter 3 Mounting the Antenna Bay(s) .........................................19

Tower leg or mounting pipe up to 3-1/2 inches outside diameter:........... 19

Figure 15 Bay mounting on pipe up to 3-1/2 inches OD.............. 19

Tower leg or mounting pipe 3-1/2 to 6 inches outside diameter: ............ 20

Figure 16 Bay mounting on pipe 3-1/2" - 6" OD........................ 20

Chapter 4 Connecting the Antenna (single-bay)..............................21

Connect the antenna bay..................................................................... 21

Figure 17 Single bay antenna connection .................................. 21

Chapter 5 Connecting the Antenna (2- to 6-bay) ............................23

Mount the power divider...................................................................... 23

Figure 18 Power divider mounting............................................. 23

Содержание 6822















































































Результаты поиска

Содержание 6822

Отзывы:

Shively Labs 6822, Инструкция по установке, эксплуатации и техническому обслуживанию, Страница: 5 / 78

Результаты поиска

Содержание 6822

Отзывы: