Shively Labs 6822 Скачать руководство пользователя страница 32

Страница: 32 / 78

Connecting the Antenna (2- to 6-bay)

Install the slugged line
section (if applicable).

In the event your antenna has non-standard bay spacing or other special fea-

tures, we may have provided you with a line section containing a "slug" to

perfect the tuning of the antenna. This piece is to be installed between the

output of the transformer (if applicable) and the input of the power divider.

CAUTION

Do not remove or modify the slug from the slugged line section. This will

ruin your antenna’s performance.

NOTE

Line section mounts are generally similar to feedline mounts and should

be installed in the same manner.

NOTE

You may need to provide a coax adapter between your transmission line

and the slugged line section.

Install the slugged line section (

, as applicable) at the input flange of

your power divider (

Figure 20

, or

) as follows:

a. Ensure there is an inner conductor connector in the slugged line section

outlet flange.

b. Attach the mounts (

) to the slugged line section, close to the ends.

c. Coat the O-ring (

, as applicable) lightly with O-Lube (supplied with

the antenna), then install it in the O-ring groove in the outlet flange.

d. Mate the flanges and secure the slugged line section to the mounting pipe.

Do not fully tighten the mounts until the flange hardware is in place.

e. Install the flange hardware kit (

, as applicable) hardware and secure

the flange. Tighten in accordance with

Table 1

on page 1.

f. Tighten the mount hardware in accordance with

Table 1

Содержание 6822















































































Результаты поиска

Содержание 6822

Отзывы:

Shively Labs 6822, Инструкция по установке, эксплуатации и техническому обслуживанию, Страница: 32 / 78

Результаты поиска

Содержание 6822

Отзывы: