Shively Labs 6822 Скачать руководство пользователя страница 27

Страница: 27 / 78

Mounting the Antenna Bay(s)

WARNING

Whenever a rigger is on the tower in the area of the antenna, shut off

the signal and lock it off so that it cannot be turned on accidentally. RF

emissions at close range are hazardous.

CAUTION

Do not attach the bays together with the RF cable before mounting

them. NEVER try to support the bays from the cable.

Tower leg or mounting
pipe up to 3-1/2 inches
outside diameter:

a. At the locations you marked on the mounting pipe (

Set up the mounting

location.

on page 1), scrape away any paint or other coating to achieve good

electrical contact.

NOTE

Mount antenna bays with feed straps up, clear of all guylines and other

obstructions.

b. Using the U-bolts (

Figure 15

), attach the antenna bays at the

marked locations.

c. Repeat for the other antenna bay(s) as applicable.
d. Align the bays to the correct azimuth and align them vertically with each

other, then tighten the mounting hardware in accordance with

Table 1

page 1.

e. Repaint the pipe as needed around the antenna bay mount.

Figure 15. Bay mounting on pipe

up to 3-1/2 inches OD

Содержание 6822















































































Результаты поиска

Содержание 6822

Отзывы:

Shively Labs 6822, Инструкция по установке, эксплуатации и техническому обслуживанию, Страница: 27 / 78

Результаты поиска

Содержание 6822

Отзывы: