Shindaiwa IDG3100M Скачать руководство пользователя страница 27

Страница: 27 / 28

Symptom

Possible Causes

Remedy

Starter motor does not
start

1.  Battery is depleted
2.  Battery is deteriorated
3.  Fuse has blown

1. Recharge battery
2. Replace battery
3. Repair

Engine does not start

1.  Close the fuel lever
2.  Low fuel
3.  Fuel is contaminated by

water or foreign material

4. Fuse has blown

1.  Open the fuel lever
2.  Supply fuel
3.  Drain water from and clean the

fuel tank and inside of fuel filter

4. Repair

Engine stops
immediately
(Stops after

monitor lamp

lights up)

1.  Low oil
2.  Water temperature rise

3.  Charging fault
4.  Overspeed fault

1. Supply oil
2. Refer to "Usable Device

Capacities" and observe the
rated output

3. Repair
4. Repair

AC power is not output

1.  Output switch is "OFF"
2.  Fuse has blown
3.  Inverter malfunction

1.  Turn to "ON"
2.  Repair
3.  Repair

AC power is not output
(Overload

monitor lamp

flashes)

1. Output is stopped

because excessive
current is output due to
the excess or faulty
consumption current of
device using the
generator

2. Output is stopped due to

inverter overheating

1. Only use device with a current

capacity that is less than the
rated value
If doing this, turn the Output
switch to "OFF" and then "ON"
again to reset the generator

2. Stop the engine, and remove

any causes that are preventing
cooling such as foreign
material obstructing the
cooling air intake side of the
inverter. Allow the inverter to
cool before restarting the
engine

Device using the
generator does not
operate
(Weak output)

1 Current of Device using

the generator exceeds
the rated value

2. Idle Control switch is

turned to "ECO"

3. Different frequencies

1. Refer to "Usable Device

Capacities"

2. Turn the Idle Control switch to

"HIGH"

3. Adjust to the specified

frequency of device using the
generator

Engine does not stop

1. Stop solenoid

malfunction

2. Fuse has blown

1. Close the fuel lever to stop the

engine and repair

2. Close the fuel lever to stop the

engine and repair

Black or white smoke is
constantly emitted from
the muffler

1. Generator is overloaded

1. Observe the rated output

Refer to "Usable Device
Capacities"

Содержание IDG3100M





























Результаты поиска

Содержание IDG3100M

Отзывы:

Бренды по названию

Популярные бренды

Shindaiwa IDG3100M, Руководство владельца и оператора

Результаты поиска

Содержание IDG3100M

Отзывы:

Бренды по названию

Популярные бренды