background image

 

 

23 

 

Remove the battery. (Refer to "6-5. Battery Inspection ".) 

 

Replace the engine oil. (Refer to "9. Inspection/Maintenance".) 

 

Drain the fuel from the fuel tank and fuel filter. (Refer to "9. 
Inspection/Maintenance".) 
 
Remove the engine key and store carefully in a secure location. 

 

Clean the entire generator, and store in a dry and dust-free location, with it covered 
or otherwise protected. 

 

<Note> 

  Recharge the removed battery approximately once a month. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Use  the  following  table  to  inspect  the  generator  when  operation  is  poor  or  faulty.  Please 
contact  the  authorized  distributor  where  this  generator  was  purchased  or  one  of  our  sales 
offices if you cannot solve a problem after performing inspection. 

Black Battery Cap (Minus Side) 

11. Troubleshooting 

8. 

 

 

 Do not touch this generator during operation if it or your body is wet. 

 Be  sure  to  always  stop  the  engine  before  performing  any  check  or 

maintenance. 

 Do not open any doors during operation. An open door could result in 

being  pinched  or  caught  in  moving  parts  such  as  the  cooling  fan  and 
belt. 

WARNING: ELECTRIC SHOCK/INJURY 

 This  generator  uses  diesel  fuel.  Be  sure  to  always  stop  the  engine 

before checking the fuel or refueling, and absolutely do not allow flame 
near  the  generator  when  performing  such  procedures.  Wait  until  the 
engine cools before performing such procedures. 

WARNING: FIRE 

 Do  not  touch  the  engine  or  surrounding  parts  while  the  generator  is 

operating  or  immediately  after  the  engine  has  stopped  because  they 
are still extremely hot. 

CAUTION: BURNS 

Содержание IDG3100M





























Отзывы: