background image

3

ENGLISH

General Safety Instructions

Wear close-fitting 

clothing to protect 

legs and arms. Gloves 

offer added protection 

and are strongly 

recommended. Do not 

wear clothing or 

jewelry that could get 

caught in machinery 

or underbrush. Secure 

long hair so that it is 

above shoulder level. 

NEVER wear shorts!

Always wear hearing 

protection devices and a 

broad-brimmed hat or 

helmet.

Keep a proper 

footing and do 

not 

overreach

Maintain your 

balance at all 

times during 

operation.

Wear appropriate footwear 

(non-skid boots or shoes). Do not 

wear open-toed shoes or sandals. 

Never work barefooted!

Always wear eye 

protection such as 

goggles or safety 

glasses.

Always wear a 

shoulder strap or a 

harness when 

operating this unit.

Always operate with both hands firmly 

gripping the machine and make sure the 

handle is positioned to provide you with 

maximum protection from contacting 

the blade or other trimmer attachments.

Keep away from the rotating 

blade or trimming line at all 

times, and never lift a moving 

attachment above waist-high.

Always make sure the cutting 

attachment is properly installed 

and firmly tightened before 

operation.

Always make sure 

the appropriate 

cutting attachment 

shield is correctly 

installed.

WARNING!

A cutting attachment shield or other 

protective device is no guarantee of 

protection against thrown objects. 

YOU MUST ALWAYS GUARD 

AGAINST FLYING DEBRIS!

WARNING!

Minimize the Risk of Fire

NEVER

 smoke or light fires near the 

trimmer or brushcutter.
Stop the engine and let it cool before 

refueling. Avoid overfilling and wipe off 

any spilled fuel.
Be careful when handling fuel. Before 

starting the engine, move the unit at least 

10 feet (3 meters) away from the fuel 

storage area or other readily flammable 

materials.

NEVER

 place flammable material close to 

the engine muffler.

NEVER

 run the engine without the spark 

arrester screen in place.

Use Good Judgment

NEVER

 run the engine when transporting 

the machine.

NEVER

 run the engine indoors; make 

sure there is always good ventilation. 

Fumes from engine exhaust can cause 

serious injury or death.
Clear your work area of debris that could 

be thrown back at you or toward a 

bystander.
Use the proper cutting tool for the job.

STOP

 the machine immediately if it 

suddenly begins to vibrate or shake. 

Inspect for broken, missing or improperly 

installed parts or attachments.

NEVER

 use a cracked or warped trimmer 

head: replace it with a serviceable one.

NEVER

 operate the unit with the cutting 

attachment shield or other protective 

devices (harness, ignition switch, blade 

safety clip etc.) removed!
Keep the machine as clean as practical. 

Keep it free of loose vegetation, mud, etc.
Keep the handles clean.
Disconnect the spark plug wire before 

performing any maintenance work.

NEVER

 make unauthorized attachment 

installations.

  Figure 1

Stay Alert

You must be physically and mentally fit to operate this ma-

chine safely. 

The Properly Equipped Operator

Work Safely

Trimmers run at very high speeds and can do serious damage 

or injury if they are misused or abused. 

Never allow a person 

without training or instruction to operate your machine.

Содержание HomePro 22C









































Отзывы: