15
P
ower
B
lower
o
Perator
'
s
M
anual
aIr
fIlter
Level 1.
Parts required:
Air Filter
NOTE
Clean daily.
1. Close choke (Cold Start Position [
]). This prevents dirt from
entering the carburetor throat when the air filter is removed. Brush
accumulated dirt from air cleaner area.
2. Remove air filter cover. Brush dirt from inside cover.
3. Remove air filter and lightly brush debris from filter. Replace
filter if it is damaged, fuel soaked, very dirty, or the rubber sealing
edges are deformed.
4. If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
5. Install air filter cover.
fuel
fIlter
Level
1.
Parts required:
Fuel Filter
WARNING
Fuel is
VERY
flammable. Use extreme ca
re when mixing, storing
or handling.
1. Use a clean rag to remove loose dirt from around fuel cap and
empty fuel tank.
2. Use the “fuel line hook” to pull the fuel line and filter from the
tank.
3. Remove the filter from the line and install the new filter.
15
Eng
lish
a
Ir fIlter
Level 1.
Tools required:
25-50 mm (1-2 in.) Cleaning brush.
NOTE
Clean daily.
Close choke (Cold Start Position [
]). This prevents dirt from enter-
ing the carburetor throat when the air filter is removed. Brush accumu
-
lated dirt from air cleaner area.
Remove air filter cover. Brush dirt from inside cover.
Remove air filter and lightly brush debris from filter. Replace filter if
it is damaged, fuel soaked, very dirty, or the rubber sealing edges are
deformed.
If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
Install air filter cover.
f
uel fIlter
Level 1.
Tools required:
200-250 mm (8-10 in.) length of wire with one end
bent into a hook, Clean rag, funnel, and an approved fuel container.
WARNING
Fuel is
VERY
flammable. Use extreme ca
re when mixing, storing
or handling.
Use a clean rag to remove loose dirt from around fuel cap and empty
fuel tank.
Use the “fuel line hook” to pull the fuel line and filter from the tank.
Remove the filter from the line and install the new filter.
1.
2.
3.
4.
5.
1.
2.
3.
15
Eng
lish
a
Ir fIlter
Level 1.
Tools required:
25-50 mm (1-2 in.) Cleaning brush.
NOTE
Clean daily.
Close choke (Cold Start Position [
]). This prevents dirt from enter-
ing the carburetor throat when the air filter is removed. Brush accumu
-
lated dirt from air cleaner area.
Remove air filter cover. Brush dirt from inside cover.
Remove air filter and lightly brush debris from filter. Replace filter if
it is damaged, fuel soaked, very dirty, or the rubber sealing edges are
deformed.
If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
Install air filter cover.
f
uel fIlter
Level 1.
Tools required:
200-250 mm (8-10 in.) length of wire with one end
bent into a hook, Clean rag, funnel, and an approved fuel container.
WARNING
Fuel is
VERY
flammable. Use extreme ca
re when mixing, storing
or handling.
Use a clean rag to remove loose dirt from around fuel cap and empty
fuel tank.
Use the “fuel line hook” to pull the fuel line and filter from the tank.
Remove the filter from the line and install the new filter.
1.
2.
3.
4.
5.
1.
2.
3.
NOTE
Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the
United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank.
When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to
replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replace
-
ment part.)
Содержание EB212
Страница 26: ...26 notes...
Страница 27: ...27 Power Blower Operator s Manual notes...
