Shindaiwa EB212, Руководство владельца/оператора

Страница: 12 / 28

12
startIng warm engIne
The starting procedure is the same as Cold Start except DO NOT close
the choke.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Throttle Position
Move throttle position lever (B) midway between idle and full
throttle positions.
3. Recoil Starter
Place the unit on a flat clear area. Firmly grasp throttle grip with
left hand and rapidly pull recoil starter handle/rope (E) until en-
gine fires.
IMPORTANT
Recoil starter: Use short pulls - only 1/2-2/3 of rope for start-
ing. Do not allow the rope to snap back in. Always hold the unit
firmly.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
stoppIng engIne
1.
Throttle Trigger/Throttle Position Lever
Release throttle trigger (F). Move throttle position lever (B)
forward to idle position and allow engine to return to idle before
shutting engine off.
2.
Stop Switch
Move stop switch (B) to "Stop" position.
WARNING
If engine does not stop when stop switch is moved to STOP posi-
tion, close choke - COLD START position - to stall engine. Have
your ECHO dealer repair stop switch before using blower again.
12
Eng
lish
A
B
E
s
tartInG Warm enGIne
The starting procedure is the same as Cold Start except DO NOT close
the choke.
Stop Switch
Move stop switch button (A) away from the STOP position.
Throttle Position
Move throttle position lever (B) midway between idle and full throttle
positions.
Recoil Starter
Place the unit on a flat clear area. Firmly grasp throttle grip with left
hand and rapidly pull recoil starter handle/rope (E) until engine fires.
IMPORTANT
Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.
Do not allow the rope to snap back in. Always hold the unit firmly.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
1.
2.
3.
s
toppInG enGIne
Throttle Trigger/Throttle Position Lever
Release throttle trigger (F). Move throttle position lever (B) forward to
idle position and allow engine to return to idle before shutting engine off.
Stop Switch
Move stop switch (B) to "Stop" position.
WARNING
If engine does not stop when stop switch is moved to STOP position,
close choke - COLD START position - to stall engine. Have your
Shindaiwa dealer repair stop switch before using blower again.
1.
2.
A
F
B
12
Eng
lish
A
B
E
s
tartInG Warm enGIne
The starting procedure is the same as Cold Start except DO NOT close
the choke.
Stop Switch
Move stop switch button (A) away from the STOP position.
Throttle Position
Move throttle position lever (B) midway between idle and full throttle
positions.
Recoil Starter
Place the unit on a flat clear area. Firmly grasp throttle grip with left
hand and rapidly pull recoil starter handle/rope (E) until engine fires.
IMPORTANT
Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.
Do not allow the rope to snap back in. Always hold the unit firmly.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
1.
2.
3.
s
toppInG enGIne
Throttle Trigger/Throttle Position Lever
Release throttle trigger (F). Move throttle position lever (B) forward to
idle position and allow engine to return to idle before shutting engine off.
Stop Switch
Move stop switch (B) to "Stop" position.
WARNING
If engine does not stop when stop switch is moved to STOP position,
close choke - COLD START position - to stall engine. Have your
Shindaiwa dealer repair stop switch before using blower again.
1.
2.
A
F
B
6. Choke
After engine fires (or 5 pulls), move choke lever to “Run” ( )
position and pull starter handle/rope until engine starts and runs.
Allow unit to warm up at idle for several minutes.
NOTE
If engine does not start with choke in “Run” position after 5 pulls,
repeat instructions 2- 5.
7. After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
11
Eng
lish
s
tartInG cold enGIne
• Provide all operators of this equipment with the Operator's Manual
and instructions for safe operation.
• Before starting the unit, equip yourself and any other person work-
ing within the 15 m (50 ft.) Safety Zone with the required Protective
Equipment and clothing.
Stop Switch
Move stop switch button (A) away from the STOP position.
Throttle Position
Move throttle position lever (B) midway between idle and full throttle
positions.
1.
2.
A
B
Choke
Move choke (C) to "Cold Start" ( ) Position.
Purge Bulb
Pump purge bulb (D) until fuel is visible and flows freely in the clear
fuel tank return line. Pump bulb an additional 4 or 5 times.
IMPORTANT
Recoil starter: Use short pulls - only 1/2-2/3 of rope for starting.
Do not allow the rope to snap back in. Always hold the unit firmly.
Recoil Starter
Place the unit on a flat, clear area. Firmly grasp throttle grip with left
hand and rapidly pull recoil starter handle/rope (E) until engine fires (5
pulls maximum).
Choke
After engine fires (or 5 pulls), move choke lever to “Run” (
) posi-
tion and pull starter handle/rope until engine starts and runs. Allow unit
to warm up at idle for several minutes.
NOTE
If engine does not start with choke in “Run” position after 5 pulls,
repeat instructions 2- 5.
After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
3.
4.
5.
6.
7.
C
D
E