Shindaiwa C242S Скачать руководство пользователя страница 8

Страница: 8 / 24

The throttle lever free play should be

approximately 4-6 mm. See Figure 10. Make

sure that the throttle lever operates smooth-

ly without binding. If it becomes necessary

to adjust the lever free play, follow the proce-

dures and illustrations that follow.

Hook Up Throttle Cable

1. Loosen the air cleaner cover knob and re-

move the air cleaner cover. See Figure 8.

Assembly and Adjustments

Figure 8

Figure 13

Knob

Air Cleaner

Cover

Adjust Throttle Lever Free Play

C35013

4-6 mm

Throttle Free Play

Figure 12

T242

C242

251043

Figure 11

3. Connect the bullet shaped end of the

throttle cable to the throttle lever on top

of the carburetor. See Figure 10.

CAUTION!

Wiring runs must not interfere with
throttle operation.

Throttle

Cable

Ignition Leads

Cable

Adjuster

Figure 9

Connect the

throttle cable

4. Connect ignition leads. See Figure 11.

Push ends

together

2. Loop the ribbed cable tube under the

tube and to the top left side of the en-

gine and push cable through the cable

adjuster. See Figure 9.

Figure 10

Assembly and Adjustments

1. Loosen the lock nut on the cable

adjuster. See Figure 12.

2. Turn the cable adjuster in or out as re-

quired to obtain proper free play 4-6 mm.

See Figure 12.

3. Tighten the locknut.
4. Reinstall the air cleaner cover.

Lock

Nut

Cable

Adjuster

Содержание C242S

























Результаты поиска

Содержание C242S

Отзывы:

Бренды по названию

Популярные бренды

Shindaiwa C242S, Руководство владельца/оператора

Результаты поиска

Содержание C242S

Отзывы:

Бренды по названию

Популярные бренды