Shindaiwa C242S Скачать руководство пользователя страница 3

Страница: 3 / 24

WARNING!

Use Good Judgment

ALWAYS

wear eye protection to shield

against thrown objects.

NEVER

run the engine when

transporting the unit.

NEVER

run the engine indoors! Make

sure there is always good ventilation.
Fumes from engine exhaust can cause
serious injury or death.

ALWAYS

clear your work area of trash

or hidden debris that could be thrown
back at you or toward a bystander.

General Safety Instructions

The Properly Equipped Operator

Always operate with both

hands firmly gripping the unit.

Wear close-fitting clothing to

protect legs and arms. Gloves

offer added protection and are

strongly recommended. Do not

wear clothing or jewelry that

could get caught in machinery

or underbrush. Secure hair

so it is above shoulder level.

NEVER wear shorts!

Wear hearing protection

devices and a broad-brimmed

hat or helmet.

Always

wear eye protection such

as goggles or safety glasses.

Keep away from the rotating

trimmer line or blade at all times,

and never lift a moving attachment

above waist-high.

Wear appropriate footwear (non-skid

boots or shoes): do not wear open-toed

shoes or sandals.

Never operate the

unit while barefoot!

Keep a proper footing and

do not over-

reach

—maintain your balance at all times

during operation.

Always

make sure the

appropriate cutting attachment

shield is correctly installed and

in good condition.

Figure 1

Always

wear a shoulder strap or a harness when

operating a unit equipped with a blade.

ALWAYS

use the proper cutting tool for

the job.

ALWAYS

stop the engine immediately

if it suddenly begins to vibrate or shake.
Inspect for broken, missing or improp-
erly installed parts or attachments.

NEVER

extend trimming line beyond

the length specified for your unit.

ALWAYS

keep the unit as clean as

practical. Keep it free of loose
vegetation, mud, etc.

ALWAYS

hold the unit firmly with both

hands when cutting or trimming, and
maintain control at all times.

ALWAYS

keep the handles clean.

ALWAYS

disconnect the spark plug

wire before performing any
maintenance work.

ALWAYS,

if a saw blade should bind

fast in a cut, shut off the engine
immediately. Push the branch or tree to
ease the bind and free the blade.

Содержание C242S

























Результаты поиска

Содержание C242S

Отзывы:

Бренды по названию

Популярные бренды

Shindaiwa C242S, Руководство владельца/оператора

Результаты поиска

Содержание C242S

Отзывы:

Бренды по названию

Популярные бренды