manualshive.com logo in svg

Shindaiwa C242S, Руководство владельца/оператора

Поделиться
Скачать
Shindaiwa C242S Скачать руководство пользователя страница 10

Turn the T242/C242 upside down so the 

gearcase output shaft is facing UP and  

remove the shaft bolt, bolt guard and 

Holder B from the gearcase shaft.
1.  Align the hole in blade Holder A with 

the matching hole in the gearcase flange 

and then temporarily lock the output 

shaft by inserting a hex wrench  

through both holes. See Figure 18.

Mount the Saw Blade.

Assembly 

Blade T242/C242

CAUTION!

Install the blade so its printed surface 
is visible to the operator when the 
brushcutter is in the normal operating 
position.

WARNING!

The blade must fit flat against the 

holder flange. The blade mounting hole 

must be centered over the raised boss 
on blade Holder A.

2.  Install blade Holder B on the output 

shaft. See Figure 19. The recess in the 

holder must fit tightly against the blade.

Shaft Bolt

Bolt Guard

Holder B

Gear Shaft

Holder A

Hex 

Wrench

  Figure 18

341015

Blade

Hex Wrench

Blade Holder B

Tighten the assembly (blade 

not shown for clarity)

  Figure 19

Output 

 

Shaft

The T242/C242  

should now be completely  

assembled and ready for  

use with a blade.

3.  Install the bolt guard and then the blade 

retaining bolt. Using the combination 

spark plug wrench/screwdriver, tighten 

the bolt firmly in a counter-clockwise 

direction.

4.  Remove the hex wrench.

10

Содержание C242S

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды