Shindaiwa C242S Скачать руководство пользователя страница 20

Страница: 20 / 24

Troubleshooting Guide (continued)

ADDITIONAL PROBLEMS

Poor acceleration.

Clogged air filter.

Clogged fuel filter.

Lean fuel/air mixture.

Idle speed set too low.

Switch turned off.

Fuel tank empty.

Clogged fuel filter.

Water in the fuel.

Shorted spark plug or loose terminal.

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected,

or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine.

Engine idle too high.

Broken clutch spring or worn clutch spring boss.

Loose attachment holder.

Engine idle set too high.

Engine has an air leak.

Warped or damaged cutting attachment.

Loose gearcase.

Bent main shaft/worn or damaged bushings.

Trimmer line not wound properly on spool.

Shaft not installed in powerhead or gearcase.

Broken shaft.

Damaged gearcase.

Clean the air filter.

Replace the fuel filter.

Consult with an authorized servicing dealer.

2,750(±250) rpm min

-1

Reset the switch and re-start.

Refuel. See page 11.

Replace fuel filter.

Drain; replace with clean fuel. See page 11.

Clean or replace spark plug, tighten the terminal.

Replace the ignition unit.

Consult with an authorized servicing dealer.

Test and replace as required.

Idle engine until cool.

Clean and regap the plug to 0.6 - 0.7 mm.

Correct plug: NGK BPMR6A or equivalent resistor

type spark plug of the correct range.

Idle engine until cool.

2,750(±250) rpm min

-1

Replace spring/shoes as required, check idle speed.

Inspect and re-tighten holders securely.

2,750(±250) rpm min

-1

Consult with an authorized servicing dealer.

Inspect and replace attachment as required.

Tighten gearcase securely.

Inspect and replace as necessary.

Rewind trimmer line.

Inspect and reinstall as required.

Consult with an authorized servicing dealer.

Symptom

Possible Cause

Remedy

Engine stops abruptly.

Engine difficult to shut off.

Excessive vibration.

Cutting attachment rotates at

engine idle.

Cutting attachment will

not rotate.

Engine will not idle down.

Содержание C242S

























Результаты поиска

Содержание C242S

Отзывы:

Бренды по названию

Популярные бренды

Shindaiwa C242S, Руководство владельца/оператора

Результаты поиска

Содержание C242S

Отзывы:

Бренды по названию

Популярные бренды