3
INSTALLATION INSTRUCTIONS
Oven B (Back)
Oven A (Back)
Screw (d)
Screw (e)
Screw (d)
Mounting
plate B
Screw (a)
Screw (c)
Screw (b)
Mounting
plate A
Screw (e)
Screw (c)
Screw (b)
Screw (a)
1. Remove all packing materials from the oven cavity. Remove the protective fi lm(blue fi lm) from the outer case cabinet. Check
the unit for any damage, such as a misaligned door, damaged door seals around the door or dents inside the oven cavity
or on the door. If there is any damage, please do not operate the oven until it has been checked by a SERVICE CENTRE
APPROVED BY SHARP and repaired, if necessary.
2. Accessories provided
1) Operation manual
2) Touch guide
3) Caution sheet (SPECIAL INSTRUCTIONS AND WARNINGS: part
code TCAUHA276WRRZ)
3. Place oven on a secure, level surface, strong enough to
take the oven weight, plus the heaviest item likely to be
cooked in the oven.
4. The oven should not be installed in any area where
excessive heat and steam are generated, for example,
next to a conventional oven unit.
The oven should be installed so as not to block ventilation
openings.
Allow at least 25 cm on the top, 10 cm on the both sides
of the oven for free air space. This applies for both single
and two ovens stacked.
When installing in a cabinet, the minimum inside
dimension of the cabinet should be as follows. For single :
645 mm (W) x 596 mm (H) x 573 mm (D). For two ovens
stacked : 645 mm (W) x 942 mm (H) x 573 mm (D). This
oven is not designed for built-in installation.
WARNING: The electrical outlet must be readily accessible so that the unit can be unplugged easily in an emergency.
5. Neither the manufacturer nor the distributors can accept any liability for damage to the machine or personal injury for failure
to observe the correct electrical connecting procedure.
The A.C. voltage must be single phase 230-240V, 50Hz.
6. It is recommended that a separate circuit serving only this appliance be provided.
7. This appliance must be earthed.
8. Operate the oven from a general purpose outlet.
If a generator is used, do not operate the oven with non-sinusoidal outputs.
9. STACKING PROCEDURE FOR TWO MICROWAVE OVENS
Two units can be installed together by placing one on top of the other. Follow these instructions:
A. Place oven A in the desired location. Position oven B on top of oven A as shown in the fi gure.
B. Remove screws (a) and mounting plate A and B from the right side of the back of oven A and B.
C. Replace screws (a) removed at step B and tighten them.
D. Remove screws (b), (c), (d), and (e) and then install mounting plate A and B which were removed at step B to the each
lower edge of oven B as shown in the fi gure.
E. Replace screws (b), (c), (d), and (e) which were removed at step D and tighten them.
WARNING:
When two ovens are installed together by placing one on top of another:
1. Always use two mounting plates.
2. Make sure that the power supply cords are not caught between the ovens.
3. Do not install more than one oven on top of another.
4. Do not lose the removed screws.
NOTE: External Equipotential Earthing Terminal
Equipment has secondary earthing terminal.
Terminal provides external earthing connection used in addition to earthing prong on plug.
Located on outside of oven back, terminal is marked with symbol shown on the right side.
R-1900J [EN].indd Sec1:3
R-1900J [EN].indd Sec1:3
6/8/09 8:50:11 AM
6/8/09 8:50:11 AM
