Sharp MX-FXX1 Скачать руководство пользователя страница 69

Страница: 69 / 80

MXFXX1 TROUBLE CODE 6 – 5

When the sub code 2 is "08" or "30" and the communication report is "OK," the report code is "00" or "16."

4. Dial tone

When shipping from the factory, the dial tone detection when send-
ing is set to Enable (changed from OFF to ON). When installing this
machine, be sure to check and confirm that the dial tone is properly
detected and the auto dial sending is enabled.

A. Check procedure

Check to confirm that the continuous buzzer sound is heard
when the on-hook key is pressed. (Press the on-hook key
again to cancel the buzzer sound.)

Change the mode to the direct send, set a sheet of send docu-
ment, enter the destination number, and start sending. Before
the destination is connected, scanning the document is
started. (The send document is not scanned if the destination
is erroneously entered or the line is busy.)
If the continuous buzzer sound is not heard and the send doc-
ument is not scanned when the on-hook key is pressed,
change the setting of the following soft SW.
SW53-4 (Dial tone detection): 1 (Yes)

→

0 (No)

If facsimile communication cannot be executed normally through
the IP telephone line, try the general telephone line.

Calling is not made (busy)<Collision detected (including CNG detection)>

Send

Not used

—

In resend of document filed data, an error occurs in decoding or coding.

Resend

In resend of document filed data, setting to inhibit resolution conversion is made. (The resolution after resend is set to be
Enlarged.)

Resend

In resend of document filed data, rotation setting is made for data which cannot be rotated.

Resend

In resend of document filed data, data cannot be stored in HD after conversion of resolution for resend.

Resend

E-mail header acquisition error

E-mail receive

Time out occurs during e-mail receive.

E-mail receive

Receive reject occurs during e-mail receive.

E-mail receive

Network communication cannot be made due to port disable.

Network send

An authentication of the POP server is failed when POP before SMTP is enabled.

Network send

There is no attached file in received e-mail.

E-mail receive

The attached file of received e-mail is not of TIFF type which is supported.

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
ID error

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
Endian error

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
Version error

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
Tag data error

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
Tag parameter error

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
Header size error

E-mail receive

The TIFF type of the attached file in received e-mail cannot be recognized.
Data error

E-mail receive

In e-mail receive, an attached file cannot be stored in memory.
Memory over.
Cannot be stored in memory.

E-mail receive

In e-mail receive, an attached file cannot be stored in memory.
The file size is too great to be stored in memory.

E-mail receive

In SMTP e-mail receive, an attached file cannot be stored in memory.
Cannot be stored in memory.

E-mail receive

Report code 2

Content of communication interruption

Send/Receive

Содержание MX-FXX1

















































































Результаты поиска

Содержание MX-FXX1

Отзывы:

Бренды по названию

Популярные бренды

Sharp MX-FXX1, Руководство по обслуживанию

Результаты поиска

Содержание MX-FXX1

Отзывы:

Бренды по названию

Популярные бренды