MX-FX11 FAX SOFTWARE SWITCH 2 – 20
111
1, 2
Print document
contents when
transmitting (results
sheet)
<FAX only>
Setting to determine whether or not to print part of the transmitted document on
the communication results sheet (transmission) when FAX transmission error
occurs.
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is set.
This functions when the communication results sheet print setting (ordinary
transmission) (broadcast transmission) is set to be outputted.
FAX initial setting
3
Automatic printing of
the record sheet when
memory is full.
Setting to determine whether or not to automatically output the communication
record sheet when transmitted and received data on the FAX/Internet FAX
communication record sheet reach 200 entries.
"0": No (do not output)
"1": Yes (automatically output)
If the data are not outputted, then new data are written over the previous data
starting from the oldest of the 200 entries.
Trigger printing of 200 entries.
FAX initial setting
4-8
Printing of the
communication record
sheet at a designated
time (hours)
Set the hours part of the designated time (hours and minutes) for outputting the
communication record sheet.
Setting can be made over the range of 0 to 23 (hours) in 1-hour increments by
binary inputting. The initial value of 0 hour is reverted to if a value outside of the
setting range is set.
FAX initial setting
112
1-6
Printing of the
communication record
sheet at a designated
time (minutes)
Set the minutes part of the designated time (hours and minutes) for outputting
the communication record sheet.
Setting can be made over the range of 0 to 59 (minutes) in 1-minute increments
by binary inputting. The initial value of 0 minute is reverted to if a value outside
of the setting range is set.
FAX initial setting
7
Printing of the
communication record
sheet at a designated
time
Setting to determine whether or not to output the communication record sheet
at a designated time.
"1": Output the communication record sheet at a designated time
"0": Do not output the communication record sheet at a designated time. Even if
designated time printing is set, do not output when the designated time
coincides with the nighttime FAX mode.
FAX initial setting
8
Not used
113
1-8
Reception
Remote changeover
number setting
Set by binary inputting the number for receiving remote changeover from
external telephones.
However, the remote changeover number is "XX*" with * fixed.
Adopt * when "A" is inputted.
Adopt # when "B" is inputted.
For bits 1-4, fix the upper digit of the remote changeover number. (0-F)
For bits 5-8, fix the second lowest digit of the remote changeover number. (0-F)
When C-F are set, the initial value is reverted to.
FAX initial setting
114
1, 2
Not used
3
Call arrival
FAX destination check
function
Function to check the FAX destination in order not to send a FAX to an
erroneous destination caused by operation mistake, etc.
"0": Disable
"1": Enable
FAX initial setting
4-7
Not used
8
Communication
External telephone
connection
Setting to determine whether or not to use an external telephone.
If "Yes" is not set using this switch, an external telephone cannot be used.
"0": No (invalid)
"1": Yes (valid)
The user cannot set without an external telephone.
FAX initial setting
115
1-7
Not used
8
Transmission
Sender's name adding
function
Setting is made whether the sender's number in the sender print is changed to
the receiver's name or not.
When it is set to the receiver's name, if the address is set by the one-touch key,
the key name of the address is printed in the sender print section.
If it is not by the one-touch key (including automatic reversing with interface),
print is not made (blank).
"0": Sender's number (Default)
"1" :Receiver's name
* This function is valid only in the special ROM (made in August, 2009).
The format of the added receiver's name is ">>Receiver's name (one-touch
key name)."
FAX initial setting
SW
No.
Bit
No.
Item
SW selection and function
System settings
