MX-FX11 FAX SOFTWARE SWITCH 2 – 10
36
6
Printing of transmitted
document contents at
times of F code
communication
<FAX only>
Setting to determine whether or not to print part of the transmitted document on
the communication results sheet at times of F code communication. However,
only when the "Document contents printing at times of transmission" setting is
valid.
"0": Do not print
"1": Print
The "Document contents printing (results sheet) at times of transmission"
setting takes priority.
7
Document content print
when sending (PC-Fax
(Internet Fax) report
table)
Setting to print images or not on the report table when sending PC-Fax
(Internet Fax).
"0": Not print
"1": Print
When the system setting is set so that images are added in the communication
report table, if the destination is a PC-Fax (Internet Fax), the document
contents are printed by this setting.
8
Not used
37
1, 2
Function
Protocol monitor
Setting to determine whether or not the protocol monitor (recognized by the
FAX) for 1 communication is printed.
"00": No (do not print)
"01": No (do not print)
"10": Print (always)
"11": Only at times of error (print)
When a new communication occurs before the protocol monitor is printed,
delete the old protocol data (overwrite).
3
Function
Determination of sub-
scan length
(determination setting
when selecting the
page)
Setting to determine whether to give priority to width or length when selecting
the optimum sheet when printing received data.
"0": Priority to data length
"1": Priority to data width
4
Paper selection when
reception printing
(LTR/A4)
Used to set whether LTR is confirmed first of all in selection of paper for
reception printing or paper that provides smaller reduction rate of A4 and LTR is
selected.
"0": Priority on LTR/A4 reduction rate
"1": Priority on LTR
5
Not used
6
Function
Valid/Invalid setting of
FAX A4, 8.5 x 11
threshold
When printing received FAX data with A4 and 8.5 x 11 paper in the tray, this
setting determines whether to make threshold values in paper selection valid or
invalid. If made valid, it becomes easier to select letters.
"0": Valid
"1": Invalid
When printing received Internet FAX data, conduct setting using the separate
SW (Valid/Invalid setting of Internet FAX A4, 8.5 x 11 threshold).
7
Reception
Setting of the reception
width of 11x17 sheet
This sets the receivable document width in cases where "11 x 17 sheet" is
selected as the FAX printing paper.
"0": A3 width (A3, B4, A4)
"1": B4 width (B4, A4)
8
Communication
Data line parity check
(Between ICU -
FAXBOX)
The parity on the data line between the ICU and the FAXBOX is checked.
(Supporting the E7-06 problem)
"0": Parity is checked.
"1": Parity is not checked.
38
1-4
Function
Magnification setting in
automatic reduction
Setting to determine the page length for reduced printing of documents
received when automatic reduced printing is set at permitted.
Percentage threshold that can be reduced (excluding reduction between fixed
page sizes)
Setting can be made over the range of 85% to 100% in 1% increments by
binary inputting (N x 1% + 85%).
The initial value of 90% is reverted to if a value outside of the setting range is
set.
5
Rotated printing
Setting to determine whether or not to rotate and output received data when
this is possible at times of receiving and printing FAX and Internet FAX data.
"0": Permitted (rotate and print)
"1": Prohibited (do not rotate and print)
6
Designation of rotation
direction when printing
on both sides and the
rear side.
Setting to determine whether to adopt vertical binding or horizontal binding
when printing on both sides.
When horizontal binding is selected, the header position on both sides (front
and rear) is printed in the same direction.
When vertical binding is selected, since the image rotates by 180 degrees, the
header position is reversed.
"0": Horizontal binding
"1": Vertical binding
7
Function
Setting of received
document output when
receiving
Setting to determine whether to output data received in FAX, Internet FAX
communications en masse or to output 1 page at a time as it is received.
"0": Save and output en masse following completion of reception
"1": Output 1 page at a time
SW
No.
Bit
No.
Item
SW selection and function
System settings
