7-19
Initial Setting
These settings are used to change the default settings
(initially set at the factory) for the various fax functions to
settings that better meet your needs.
Select the [Initial Setting] to configure the settings.
Dial Mode
This setting is used to set the appropriate dial mode for
the line connected to the machine. Select tone for a tone
dial line or pulse for a pulse dial line.
Pause Time
This setting is used to select the duration of pauses that
are inserted in destination fax numbers.
Normally the setting is 2 seconds, which means that
each time the [PAUSE] key is pressed when dialing or
storing a fax number, a pause of 2 seconds is inserted.
The pause time can be set to any number of seconds
from 1 to 15.
Own Passcode Set
Use this setting to setting the fax number of the machine
and the name of the user. The programmed name and
number are printed at the top of each fax page you send.
The number is also used as a passcode when performing
polling reception
".
You can check your programmed name and number by
printing out the
A maximum of 20 digits can be stored for the fax number.
• A maximum of 18 letters can be stored for the name.
Set Volume
This setting is used to adjust the on-hook volume, the
ringing volume, the line monitor volume, the TX/RX end
sound volume, and the original scanning end sound
volume.
• "High", "Middle" or "Low" can be selected for the on
hook volume.
• "High", "Middle", "Low" or "Off" can be selected for
volumes other than the on hook volume.
TX/RX End Sound
This setting is used to select the beep pattern that
signals the end of transmission or reception.
"Pattern 1", "Pattern 2" or "Pattern 3" can be selected.
Before pressing the [OK] key to store your selection, you
can press the key to listen to the selected pattern.
End Sound Length
This setting is used to select the length of the end sound
in seconds. Selections are "2.0 sec", "2.5 sec", "3.0 sec",
"3.5 sec", and "4.0 sec". "3.0 sec" is normally selected.
Distinctive Ring
If multiple telephone numbers have been assigned to
your telephone line, the number called can be identified
by its ringing pattern. By using one number for voice
calls and another number for faxes, you can tell which
type of call you are receiving by the ringing pattern. You
can set your machine to automatically receive faxes
when your fax number is called by setting the pattern
that corresponds to your fax number. Normally "Off" is
selected.
Remote Reception
(Only when an extension phone is connected)
When a call is received on an extension phone
connected to the machine, fax reception can be
activated by entering a 1-digit number and pressing
twice on the phone's keypad. This 1-digit number is
called the remote reception number, and you can set it to
any number from "0" to "9". Normally the remote
reception number is set to "5".
Disable Fax Print Hold
This setting is used to disable the fax print hold function,
which holds received faxes in memory instead of printing
them as they are received.
Normally the fax print hold function is disabled.
• The setting (which disables fax print hold) is enabled
and a checkmark appears in the checkbox.
• If this procedure is performed when the setting is
enabled, the checkmark will be cleared and the setting
disabled (fax print hold is enabled).
To clear the programmed fax number and name,
follow these steps:
(1) Select "Delete" and then press the [OK] key.
(2) Select "Delete" with the [ ] or [ ] key and then
press the [OK] key.
Item
Factory default setting
On Hook Volume
Middle
Ringer Volume
Low
Line Monitor Vol
Off
TX/RX End Volume
Low
Scan End Volume
Middle
If a remote number has been previously stored, the
newly entered remote number overwrites the old
number.
Содержание MX-B350W
Страница 306: ...2018D US1 ...
