Switching on/off
Turning on/off the power
Press
a
on the TV.
Switch it off by pressing
a
on the TV.
• However, please bear in mind that EPG data (electronic
programme guide) will be lost, and programmed timer
recordings will not be performed by the TV.
Standby mode
If the TV set is switched on, you can switch it to
standby by pressing
B
on the remote control.
Switching on from standby
From standby, press
B
on the remote control or
pressing any of the numeric buttons
0 - 9
.
Or, switch on the TV set with
OK
, you can then see the
station list and select a station.
Switching on the radio
From standby, press
RADIO
on the remote control.
Daily operation
TV indicator status
There are three indicators at the front of the TV. Refer
to the table for each LED status.
B
indicator
Status
Off
Power off
Blue
Power on
Red
Standby
STATUS
indicator
Status
Red
On Timer is programmed.
Red flashing
Receiving remote control command
Green
HDD recording timer is programmed.
Green flashing
Receiving EPG data
Orange
Both HDD recording timer and On Timer are
programmed.
HDD indicator
Status
Red
HDD recording in progress
Green
Archive playback or Time Shift recording in progress
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when
a
is
turned off.
Changing channels
With P
r
/P
s
:
Press
P
r
/
P
s
to select channels.
• The station display with audio format displays briefly.
• If favourites are set, only the registered channels are
selected with
P
r
/
P
s
. (Page 13)
• The symbols for the audio format is provided on page 13.
• If there are additional languages or DVB subtitles
for DVB stations, its selections are shown under the
station display. (Page 13)
With 0 - 9:
Press
0 - 9
to select channels.
With station list:
Press
OK
with no other menu screen active. (If
favourites list is displayed instead, press
RED
.)
Station list
EXT3
EXT5
EXT6
Press
a
/
b
/
c
/
d
or
0 - 9
to select the desired
channel in the station list, and then press
OK
to
tune in.
• Press
RED
to go to the favourites list.
• Press
BLUE
to sort the list according to
“alphabetical” or “numerical”.
• If sorted alphabetically, enter the initial letters with
0
- 9
like on a mobile phone keypad. The first station
for the specified letters is marked.
To delete, restore, move, and rename stations
from the station list
While in the station list, press
YELLOW
(Change
stations).
E
Delete
Select a station to delete, and then press
RED
(Delete). Mark more stations with
a
/
b
/
c
/
d
or
0 - 9
, if desired. Confirm with
OK
or cancel with
RED
.
E
Restore stations
To restore station(s) that you have already
deleted, select a station to restore, and then
press
GREEN
(Restore stations). Confirm with
OK
.
• The restored station is sorted according to its signal
source at the end of the respective signal block.
E
Move
Select a station to move, and then press
YELLOW
(Move). Mark more stations with
a
/
b
/
c
/
d
or
0 - 9
, if desired. Press
OK
to finish
marking.
Press
a
/
b
/
c
/
d
or
0 - 9
to select the position
to move to. Confirm with
OK
or cancel with
YELLOW
.
• Make sure to select the appropriate block of
channels or destination when moving.
E
Rename
Select a station to rename, and then press
BLUE
(Rename). Press any of the numeric
buttons
0 - 9
to select the desired character.
Remember to press and toggle the numeric
button quickly, for the transition to the next digit
is rather quick. Repeat until the new name is
fully spelt out. Confirm with
OK
or cancel with
BLUE
.
• The name can be up to 9 characters.
• Available only in the analogue TV mode.
1
2
12
LC-52HD1E-gb.indd 12
LC-52HD1E-gb.indd 12
2008/03/24 15:00:46
2008/03/24 15:00:46
Downloaded From TV-Manual.com Manuals
