Sharp IV-S51M Скачать руководство пользователя страница 5

Страница: 5 / 40

1 - 1

1. System Configuration

AC-DC Converter
commercially available
power supply

Programmable controller

Parallel input

(16 input terminals)

Parallel output

(16 output terminals)

General-purpose serial
I/F (RS-232C/RS-422)

(Accessory for the IV-S51M)

24V DC

100V AC

Extension terminal
RS-232C/RS-422

IV-S51M
Controller

USB terminal

100BASE-TX/10BASE-T

Monitor cable
IV-S50MC2

Analog RGB output

Power supply module for lighting, etc.

For future extension (USB storage, etc.)

USB mouse,
USB trackball

Commercially available analog RGB monitor

LCD monitor for IV-08MP
(built-in touch panel)

Supporting tool IV-S50SPM
Optical system selection expert

Camera cable
IV-S30KC3(3m)
IV-S30KC5(5m)
IV-S30KC7(7m)

Standard lens

(IV-S20L16)

Standard camera

(IV-S30C1)

High-speed camera

(IV-S30C3)

Camera cable
IV-S30KC3(3m)
IV-S30KC5(5m)

Standard lens

(IV-S20L16)

Camera cable
IV-S30KC3(3m)
IV-S30KC5(5m)

Micro, high-speed camera

(IV-S30C4)

Camera cable
IV-S30KC3(3m)
IV-S30KC5(5m)
IV-S30KC7(7m)

Micro camera
(IV-S30C2)

ø17 lens

(off-the-shelf product)

ø17 lens

(off-the-shelf product)

When an IV monitor is not directly connected

(Note)

• Only connect or disconnect the camera

connectors while the power is OFF.

• Push the convex side of the connector

into the concave side of the mating

connector. When the connector is all the

way on, it clicks. To disconnect the

connector, hold the plug of the connector,

and pull it straight out.

• You must have a camera connected to the

camera1 connector.

Содержание IV-S51M









































Результаты поиска

Содержание IV-S51M

Отзывы:

Похожие инструкции для IV-S51M

Бренды по названию

Популярные бренды

Sharp IV-S51M, Инструкция по эксплуатации

Результаты поиска

Содержание IV-S51M

Отзывы:

Похожие инструкции для IV-S51M

Бренды по названию

Популярные бренды