Sharp IV-S51M Скачать руководство пользователя страница 15

Страница: 15 / 40

3 - 7

Connect the camera cable (IV-S30KC3/KC5/KC7) or the camera conversion cable (IV-S30HC) to

the camera 1 connector (CAMERA 1) and camera 2 connector (CAMERA 2) on the IV-S51M.

(Note)

Only connect or disconnect the peripheral equipment including the camera while the

power is OFF.

• Push the convex side of the connector into the concave side of the mating connector. When

the connector is all the way on, it clicks.

• To disconnect the connector, hold the plug of the connector and pull it straight out.

• A camera connected to the camera 1 connector (CAMERA 1), is treated as camera 1 by this

system, and a camera connected to the camera 2 connector (CAMERA 2) is treated as

camera 2.

• It is possible to connect only one camera. In this case, you must have a camera connected to

the camera 1 connector.

LINK

RGB

ANALOG

EXP

TERMINATOR

USB

LAN

IV MONITOR

ONLY

COM

IV-S51M

POWER

CAMERA2

CAMERA1

X15

X14

X13

X12

X11

X10

C (+)

+0V

+24V

C (-)

RDY

HALT

Y15

Y14

Y13

Y12

Y11

Y10

Analog RGB monitor connector
(ANALOG RGB)

Connector for exclusive monitor
(IV MONITOR ONLY)

Camera 1 connector
(CAMERA 1)

Camera 2 connector
(CAMERA 2)

Analog RGB monitor cable
(off-the-shelf product)

Commercially available

analog RGB monitor

LCD monitor

(IV-08MP)

IV monitor cable
(IV-S50MC2: to be sold separately)

Camera 1

Camera 2

[ 3 ] Connecting the peripheral equipment to the IV-S51M

Connect the camera (up to 2 cameras), the LCD monitor, and commercially available analog RGB

monitor to the IV-S51M.

Содержание IV-S51M









































Результаты поиска

Содержание IV-S51M

Отзывы:

Похожие инструкции для IV-S51M

Бренды по названию

Популярные бренды

Sharp IV-S51M, Инструкция по эксплуатации

Результаты поиска

Содержание IV-S51M

Отзывы:

Похожие инструкции для IV-S51M

Бренды по названию

Популярные бренды