Sharp IMAGER AR-5316 Скачать руководство пользователя

Страница: 13 / 56

AR-5316 ADJUSTMENT 6-6

(3)Main scanning direction (FR direction) distortion

adjustment

This adjustment must be performed in the following cases:

•When the mirror base drive wire is replaced.
•When the lamp unit, or No. 2/3 mirror holder is replaced.

•When a copy as shown is made.

1) Set A3 (11" x 17") white paper on the original table as shown below.

2) Open the original cover and make a normal (100%) copy.

3) Measure the width of the black background at the lead edge and at

the rear edge.

If the width (La) of the black background at the lead edge is equal that

(Lb) at the rear edge, there is no need to execute the following

procedures of 4) ~ 7).

4) Loosen the mirror base drive pulley fixing screw on the front frame

side or on the rear frame side.

5)Tighten the mirror base drive pulley fixing screw.

<Adjustment specification>

La = Lb

6) Execute the main scanning direction (FR) distartion balance

adjustment previously described in 2) again.

(4) Sub scanning direction (scanning direction) distortion

adjustment

When there is no skew copy in the mirror base scanning direction and

there is no horizontal error (right angle to the scanning direction), the

adjustment can be made by adjusting the No. 2/3 mirror base unit rail
height.

Before performing this adjustment, be sure to perform the horizontal

image distortion adjustment in the laser scanner section.
This adjustment must be performed in the following cases:

•When the mirror base wire is replaced.

•When the copy lamp unit or No. 2/3 mirror unit is replaced.
•When the mirror unit rail is replaced or moved.

•When a following copy is made.

Original

Copy

Paper exit
direction

Fit the paper edge and
the glass holding plate edge.

A3 (11" x 17") white paper

Glass holding plate

Allow a little space.

Paper exit direction

La: Lead edge black background width
Lb: Rear edge black background width

Rear side

Front side

When La < Lb

Turn the mirror base drive pulley on the front frame side in the
arrow direction A.
(Do not move the mirror base drive pulley shaft.)

When La > Lb

Turn the mirror base drive pulley on the front frame side in the
arrow direction A.
(Do not move the mirror base drive pulley shaft.)

Original

Copy A

Copy B

[06]ADJUSTMENT.fm 6 ページ２００５年７月１日金曜日午後５時２７分

Содержание IMAGER AR-5316

























































Результаты поиска

Содержание IMAGER AR-5316

Отзывы:

Похожие инструкции для IMAGER AR-5316

Бренды по названию

Популярные бренды

Sharp IMAGER AR-5316, Руководство по обслуживанию

Результаты поиска

Содержание IMAGER AR-5316

Отзывы:

Похожие инструкции для IMAGER AR-5316

Бренды по названию

Популярные бренды