Sharp IMAGER AR-5316 Скачать руководство пользователя

Страница: 10 / 56

AR-5316 ADJUSTMENT 6-3

9) Measure the distance H between the paper lead edge and the image

print start position. Set the image print start position set value

(Exposure display <<AUTO+MAIN CASSETTE LAMP>> ON) again.

•1 step of the set value corresponds to about 0.1mm shift.
•Calculate the set value from the formula below.

H/0.1(mm) = Image print start position set value

<H: Print start position measurement value (mm)>

Example:

5/0.1 = 50 = about 50

Note: If the set value is not obtained from the above formula, perform the

fine adjustment.

10) Set the lead edge void adjustment value (Exposure display

<<TEXT>> ON)* again.

•1 step of the set value corresponds to about 0.1mm shift.

•Calculate the set value from the formula below.

B/0.05 (mm) = Lead edge void adjustment value
<B: Lead edge void (mm)>

Example:

When setting the lead edge void to 2.5mm
:2.5 /0.05 = about 50

Note: If the set value is not obtained from the above formula, perform the

fine adjustment.

Multi bypass tray lead edge void adjustment: Exposure display

<<TEXT + PHOTO>>

b.SPF image lead edge position adjustment (SIM50-6)

1) Set a scale on the OC table as shown below.

Note: Since the printed copy is used as a test chart, put the scale in

paralled with the edge lines.

2) Make a copy, Then use the copy output as an original to make an

SPF copy again.

3) Check the copy output. If necessary, perform the following

adjustment procedures.

4) Execute SIM 50-6.

5) Set the SPF lead edge position set value (Exposure display

<<AUTO>> ON) so that the same image is obtained as that obtained

in the previous OC image lead edge position adjustment.

<Adjustment specification>

Adjustment

mode

SIM

LED

Set

value

Spec

value

Set

range

OC image lead
edge position

SIM
50-1

PHOTO

R/0.1

Lead edge

void:
1 - 4mm

Image loss:
3mm or
less

1 ~ 99

Main cassette
print start
position

AUTO

MAIN

B/0.1

Multi bypass
tray print start
position

AUTO

MULTI

Lead edge void

TEXT

B/0.05

0mm

Fit the print edge with the paper edge, and perform the

lead edge adjustment.

2.5mm

Adjustment mode

SIM

LED

Set value Spec value

Set

range

SPF image lead
edge position
(1st print surface)

SIM
50-6

AUTO

1 step:
0.1mm shift

Lead edge
void:
1 - 4mm

Image loss:
3mm or
less

1 ~ 99

[06]ADJUSTMENT.fm 3 ページ２００５年７月１日金曜日午後５時２７分

Содержание IMAGER AR-5316

























































Результаты поиска

Содержание IMAGER AR-5316

Отзывы:

Похожие инструкции для IMAGER AR-5316

Бренды по названию

Популярные бренды

Sharp IMAGER AR-5316, Руководство по обслуживанию

Результаты поиска

Содержание IMAGER AR-5316

Отзывы:

Похожие инструкции для IMAGER AR-5316

Бренды по названию

Популярные бренды