manualshive.com logo in svg

Sharp FO-A760, Руководство по эксплуатации

Поделиться
Скачать
Sharp FO-A760 Скачать руководство пользователя страница 13

Unpacking Checklist

9

1. Installation

Points to keep in mind when 
setting up

♦

Do not place the machine in direct 
sunlight.

♦

Do not place the machine near 
heaters or air conditioners.

♦

Keep dust away from the machine.

♦

Keep the area around the machine 
clear.

About condensation

If the machine is moved from a cold to a 
warm place, condensation may form on 
the scanning glass, preventing proper 
document scanning. To remove the 
condensation, turn on the power and 
wait approximately two hours before 
using the machine.

1.  Installation

Unpacking Checklist

Setup

Handset

Handset 
cord

Phone 
line cord

Manual

Sample roll of 
imaging film (already 
loaded in machine)

Connecting the handset

Connecting the power cord

Plug the power cord into a 

230-240 V, 

50 Hz

, earthed (3-prong) AC outlet.

♦

The power outlet must be installed 
near the equipment and must be 
easily accessible.

Adapter

When disconnecting the machine, 
always disconnect the phone line 
before you disconnect the power cord. 
When re-connecting the machine, 
always connect the power cord before 
connecting the phone line.

It is recommended that you install 
surge protectors for the power and 
telephone lines. Surge protectors can 
be purchased at most telephone 
specialty stores.

Содержание FO-A760






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды