Sharp CD-DD4500, Руководство по обслуживанию

Страница: 2 / 88

CD-DD4500
– 2 –
CD player
Type 3-disc multi-play compact disc player
Signal readout Non-contact, 3-beam semiconductor laser pickup
D/A converter 1-bit D/A converter
Frequency response 20 - 20,000 Hz
Dynamic range 100 dB (1 kHz)
Tuner
Frequency range FM: 87.5-108 MHz
AM: 530-1,720 kHz
Cassette deck
Frequency response 50 -14,000 Hz (Normal tape)
Signal/noise ratio 55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/playback)
Wow and flutter 0.25 % (WRMS)
General
Power source AC 120 V, 60 Hz
Power consumption 230 W
Dimensions Width: 10-11/16" (270 mm)
Height: 13" (330 mm)
Depth: 14-11/16" (372 mm)
Weight 19.4 lbs (8.8 kg)
Amplifier
Output power Front speakers (Main) : 30 W minimum RMS per chan-
nel into 8 ohms.
Front speakers (Subwoofer) : 40 W per channel : 6 ohms
(100 Hz, 10 % T.H.D.)
Center speaker : 30W : 6 ohms
(1 kHz, 10 % T.H.D.)
Surround speakers : 20W per channel : 8 ohms
(1 kHz, 10 % T.H.D.)
Output terminals Front speakers (Main) : 8 ohms
Front speakers (Subwoofer) : 6 ohms
Center speaker : 6 ohms
Surround speakers : 8 ohms
Subwoofer(Pre-out) : 10 kohms
Headphones : 16-50 ohms (recommended; 32 ohms)
Input terminals DVD (Digital) : Optical
VCR/Auxiliary : 500 mV/47 kohms
Type 3 - way, 5-1/8" (130 mm) subwoofer, 4" (100 mm)
woofer and 2" (50 mm) tweeter
Maximum input power Subwoofer: 80 W
Main: 60 W
Impedance Subwoofer: 6 ohms/ Main: 8 ohms
Dimensions Width: 8- 5/8" (220 mm)
Height: 13" (330 mm)
Depth: 9- 5/8" (245 mm)
Weight 9.0 lbs. (4.1 kg)/each
Type Full range, 4" (100 mm)
Maximum input power 60 W
Impedance 6 ohms
Dimensions Width: 10- 1/4" (260 mm)
Height: 5- 5/8" (142 mm)
Depth: 6- 11/16" (170 mm)
Weight 2.2 lbs. (1.0 kg)/each
Type Full range, 4" (100 mm)
Maximum input power 40 W
Impedance 8 ohms
Dimensions Width: 7- 7/8" (200 mm)
Height: 6- 3/4" (172 mm)
Depth: 3- 3/4" (95 mm)
Weight 1.3 lbs. (0.6 kg)/each
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
Specifications for this model are subject to change without
prior notice.
SPECIFICATIONS
CD-DD4500
CP-DD4500
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment covers
or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15
µ
F capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the
resistor (See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
TEST PROBE
0.15
µ
F
1.5k ohms
10W
VTVM
AC SCALE
GBOXS0064AWM1
GBOXS2008AWM1
GBOXS4008AWM1