Sharp AL-2021 Скачать руководство пользователя страница 57

Страница: 57 / 120

AL-2041 DISASSEMBLY AND ASSEMBLY 8 - 16

8. Power section

A. List

B. Disassembly procedure

1) Disconnect each connector.

2) Remove the screw, and remove the earth line.

3) Remove two screws, and remove the power PWB unit.

C. Assembly procedure

For assembly, reverse the disassembly procedure.

9. Duplex motor section (AL-2041)

A. List

B. Disassembly procedure

1) Remove the rear cabinet.

2) Remove two screws.

3) Remove the Duplex motor cover.

4) Remove the Duplex motor.

Note: When reassembling, be sure to engage the Duplex motor

gear with the belt on the main body side.

C. Assembly procedure

For assembly, reverse the disassembly procedure.

10. Reverse roller section

A. List

B. Disassembly procedure

1) Remove four screws.

2) Remove the spring, and the earth wire.

3) Remove the reverse unit.

4) Bend the reverse roller and remove it.

C. Assembly procedure

For assembly, reverse the disassembly procedure.

No.

Part name Ref.

Power PWB

No.

Part name Ref.

Duplex motor

No.

Part name Ref.

Reverse roller

Содержание AL-2021

























































































































Результаты поиска

Содержание AL-2021

Отзывы:

Похожие инструкции для AL-2021

Бренды по названию

Популярные бренды

Sharp AL-2021, Руководство по обслуживанию

Результаты поиска

Содержание AL-2021

Отзывы:

Похожие инструкции для AL-2021

Бренды по названию

Популярные бренды