manualshive.com logo in svg

Sharp 32LF-94EC, Руководство по обслуживанию, Страница: 71 / 82

Поделиться
Скачать
Sharp 32LF-94EC Скачать руководство пользователя страница 71

 

47 

AK53 D.O.C. Service Manual 

 

22/03/2004

 

14.4.SOUND RELATED OPTIONS 

Select Sound in Service main menu by pressing “? /? ” buttons and press “? ” button to enter Sound 
menu. The following menu appears on the screen. 
 

SOUND 

 

1 NICAM I PRESCALE 

31 

2 SUBWOOFER 

ON/OFF 

3 HEADPHONE 

ON/OFF 

4 LINE OUTPUT 

ON/OFF 

 LOUDNESS 

ON/OFF 

 

NICAM I PRESCALE 

Is used to adjust power outputs for NICAM I standards, for other standards and scart no prescale value 
is needed, those are automatically adjusted within SW. 
 

SUBWOOFER 

If in the product subwoofer feature is available select as ON. Otherwise select as OFF. 
 

HEADPHONE 

If it is selected as ON, headphone menu appears in the Sound menu, otherwise does not. 

 
LINE OUTPUT 

If Line Output is supported by TV set then set this item as ON. Otherwise OFF is selected. (This feature 
is used to use external audio power amplifiers.) 
 

LOUDNESS 

If Loudness is supported by TV set then set this item as ON. Otherwise OFF is selected. 

Содержание 32LF-94EC



















































































Отзывы:

Нет отзывов