manualshive.com logo in svg

Sharp 32LF-94EC, Руководство по обслуживанию, Страница: 56 / 82

Поделиться
Скачать
Sharp 32LF-94EC Скачать руководство пользователя страница 56

 

32 

AK53 D.O.C. Service Manual 

 

22/03/2004

 

12.16.TL431 (Q816) 
12.16.1.Description 

The TL431 is a 3-terminal adjustable shunt voltage regulator providing a highly accurate 1 % band gap 
reference. TL431 acts as an open-loop error amplifier with a 2.5V temperature compensation reference. 
The TL431 thermal stability, wide operating current (150mA) and temperature range (0.to 105.makes it 
suitable for all variety of application that are looking for a low cost solution with high performance. The 
output voltage may be adjusted to any value between VREF and 36 volts with two external resistors. 
The TL431 is operating in full industrial temperature range of 0°C to 105°C. 
 

12.16.2.Features 

• Trimmed Band gap to 1%  
• Wide Operating Current  

 

 

1mA to 150mA  

• Extended Temperature Range  

 

0 °C to 105°C  

 

12.16.3.Pin Configurations 

 

bottom view 
 

12.17.TFMS5360 

Is located on front boards (keyboards) of the TV set 

12.17.1.Description 

The TFMS5360 is a miniature receiver for infrared remote control systems. 
 

 

 

12.17.2.Features 

• Photo detector and preamplifier in one. 
• 36 KHZ 
• Pin diode and preamp 
• IR filter. 
 

Содержание 32LF-94EC



















































































Отзывы:

Нет отзывов