background image

sharkclean .com

sharkclean .com

EMPTYING THE DUST CUP

To remove 

Dust Cup

, lift the latches on both 

sides, then lift off the dust cup.

To reinstall, place the bottom of the dust 

cup into the pod and then tilt until it fits into 

place. Reattach side latches.

Hold the dust cup over a trash receptacle and 

press the door release button. Tap gently to 

empty. Press the door shut until it clicks into 

place. 

To remove debris from the 

Lint Screen

 in the 

dust cup, press the top release button and 

lift the handle to open. Gently brush debris 

off the screen.

RINSE HEPA FILTER  

EVERY YEAR 

To access the 

HEPA Filter

, press the button 

on the bottom of the 

Filter Door

 and lift it 

off. Pull out the HEPA filter. To reinstall, insert 
the HEPA filter into the pod and replace the 
filter door. 

CLEAN PRE-MOTOR FILTERS  

EVERY 3 MONTHS 

Remove the dust cup, then lift out the 

Pre-Motor 

Filters

.

Regularly rinse and replace the filters to maintain your vacuum's suction power.

To prevent damage from cleaning chemicals, rinse filters with cold water only. Allow all filters 

to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into 

electric parts.

CLEANING AND REPLACING THE FILTERS

CLEANING FILTERS

IMPORTANT: 

DO NOT

 use soap when cleaning the filters.

IMPORTANT: 

Unplug the power cord before performing any maintenance. Empty 

the dust cup each time you vacuum and periodically during cleaning, when debris 

in the dust cup reaches  the MAX fill line.

Foam

Felt

NOTE:

 To order replacement parts and filters, visit 

sharkaccessories.com

.

Filter 

Door

Replacement   

Pre-Motor Foam & 

Felt Filter Kit 

XFF350

Replacement   

HEPA Filter

 

XHF350

Follow the previous instructions for removing filters. The 

Pre-Motor Filter

 should be replaced every  

2.5 years. The 

HEPA Filter

 should be replaced every 3 years.

REPLACING FILTERS

Содержание Navigator Lift-Away NV380 Series










Отзывы: