SGS SPG2200 Скачать руководство пользователя страница 10

PAGE 19

PAGE 18

GENERATOR TROUBLESHOOTING

PROBLEM

SOLUTION

Generator will not start.

•  Check fuel valve tap is in the ‘down’ 

position.

•  Check the oil level is correct.
•  Check 10W30 oil is being used.
•  Check choke is in the correct position 

(refer to starting methods).

•  Check there is a spark - Remove your 

HT (high tension) lead from the top of 
your spark plug. Remove the spark plug 
and reconnect the lead, then touch the 
metal on the spark plug against the 
generator frame. Gently pull the starter 
cord mechanism, listen for an audible 
‘ticking’ sound and/or small flashes 
coming from the very tip of the spark 
plug. If there is no audible ‘ticking’ and/
or small flashes, the spark plug may 
need replacing.

Generator is difficult to 
start.

•  The air filter is dirty - clean the filter
•  The fuel filter is dirty - clean the filter
•  If the pull start mechanism is too ‘hard’ 

when trying to pull it, it may denote that 
there is too much oil. Check the oil level 
by using the dipstick and drain excess 
oil from the oil sump bolt at the bottom 
of the generator.

•  If the pull start mechanism feels too 

‘slack’ (i.e easy to pull), there may be 
not enough compression in the genera-
tor engine for it to work properly. Please 
contact SGS Engineering.

GENERATOR TROUBLESHOOTING

PROBLEM

SOLUTION

No electrical output.

•  Check the breaker switch is up.
•  The device being powered is faulty.
•  Check that the voltage output switch is set 

to 115 or 230V. 

•  Check the connecting lead from the appli-

ance/tool into the generator is physically 
sound.

Engine making “rev-
ving” sounds

•     If your generator is ‘hunting’ (surging), it 

may need a carburettor adjustment. Turn 
the brass screw on the carburettor clockwise 
slowly and listen for the engine sound. If it 
does not improve then try turning the screw 
anticlockwise.

See our help and advice section for videos and guides on 
setting up, starting and maintaining your generator.

http://www.sgs-engineering.com/help-advice

WWW.SGS-ENGINEERING.COM
CALL FOR ASSISTANCE: 

01332 576 850

Содержание SPG2200

















Отзывы: