background image

14

•  Check oil level monitoring on the lift. Repeat the procedure if neces

-

sary.

3.4. 

Setup and installation location for FKE

Depending on the model, the pit lift is guided on the pit floor in or

on running rails, or it is freely movable on the floor of the pit.

Chassis model Z

Model Z has a chassis that runs on the floor in U-profiles, L-profiles or a 

flat steel plate

 

installed at the site (preferably U100). The profiles must 

be aligned exactly parallel, to within 10 mm. To install the rollers, open 

the U-profile at a suitable location. 

The pit lift is also freely movable crosswise in the chassis.

 

► Important! Before inserting the chassis and lift in the U-profile, they 

must be secured so that they cannot move.

Chassis model F

The F model has a chassis which runs along the floor, similar to the Z 

model. A flat steel plate can be used for the running surface. The rollers 

of the lift then run on the flat steel. This chassis can be guided laterally 

in the pit by means of adjustable spacer rollers.

Chassis model FV

The chassis of this lift is freely movable up to 1,000 kg on steering 

rollers. Loads exceeding 1,000 kg push down on the springs, so that 

the frame is on the floor. The lift is bolted solidly to the midpoint. The 

running rollers of the lift then run directly on the floor of the pit. The floor 

must be suitable for this purpose, i.e. level, solid and clean.

Chassis model FV-Q

A chassis model FV. In addition the lift can also be moved crossways 

on its chassis. Under normal conditions, the lift is completely stable. 

Since the chassis is not secured on the floor against tipping, you should 

be aware of the resulting dangers. Extreme side loading on a lift that 

can be moved laterally can result in additional tipping moments. There

-

fore, side loading should always be avoided.

3.5. 

Electrical connection

The pit lift may be connected only to a 3-phase 400 V supply with 3x16 

A fuses. After connection, run the motor just briefly. If the pump does 

not supply oil (the piston rod does not extend), then 2 phases must 

Содержание FKE





























Отзывы: