SG Models Radial Rocket TD 10cc Скачать руководство пользователя страница 29

Instruction Manual.

29

BALANCING.

1)  It is critical that your airplane be

balanced correctly. Improper balance will

cause your plane to lose control and 

crash. THE CENTER OF GRAV-

ITY IS LOCATED 

88MM

 BACK 

FROM THE LEADING EDGE OF 

THE WING AT THE WING ROOT.

3) With the model inverted, place your 

fingers on the masking tape and carefully

lift the plane.

  Accurately mark the balance point on the 

top of the wing on both sides of the fuse-

lage. The balance point is located 88mm 

back from the leading edge of the

wing at the wing root. This is the balance

point at which your model should balance 

for your first flights. Later, you may wish 

to experiment by shifting the balance up 

to 10mm forward or back to change the 

flying characteristics. Moving the balance 

forward may improve the smoothness 

and arrow- like tracking, but it may then 

require more speed for take off and make 

it more difficult to slow down for landing. 

Moving the balance aft makes the model 

more agile with a lighter and snappier 

”feel”. In any case,please start at the loca-

tion we recommend .

2) Mount the wing to the fuselage. Using

a couple of pieces of masking tape, place 

them on the top side of the wing 88mm 

back from the leading edge of the wing at 

the wing root.

 With the wing attached to the fuselage, 

all parts of the model installed ( ready to 

fly), and empty fuel tanks, hold the model 

at the marked balance point with the sta-

bilizer level.

 Lift the model. If the tail drops when 

you lift, the model is “tail heavy” and you 

must add weight* to the nose. If the nose 

drops, it is “nose heavy” and you must 

add weight* to the tail to balance.

*If possible, first attempt to balance the 

model by changing the position of the re-

ceiver battery and receiver. If you are un-

able to obtain good balance by doing so, 

then it will be necessary to add weight to 

the nose or tail to achieve the

proper balance point.

88 mm

CONTROL THROWS.

Ailerons:

High Rate  : 

12mm

Low Rate  : 

10mm 

Elevator:

High Rate  : 

12mm   

Low Rate  : 

10 mm

Rudder:

High Rate  : 

30mm   

Low Rate  : 

20 mm

Содержание Radial Rocket TD 10cc
































Отзывы: